Models > 3100SPA Maytag > Instructions

3100SPA Magic Chef Range - Instructions

All installation instructions for 3100SPA parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 3100SPA
1-15 of 25
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven rack lost in a garage fire

  • Customer: Bob from Saint Clair Shores MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 13 of 16 people found this instruction helpful
First I opened the door to the oven. Then I opened the box that the part came in. (knife) I then slid the oven rack out of the box and unwrapped the plastic, being careful not to bend or scratch the new rack. Now, this is the tricky part... I had to move the existing rack down one space to make room for the new one. Then carefully slid the new rack in, tipping it slightly and sliding it in. LOL

worn out door seal

  • Customer: Stella from Charlotte TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 11 of 12 people found this instruction helpful
removed old clips and remaining parts of old seal...new part already had clips attached, so just snapped them into holes in oven door.

Door Seal on oven was old, hard and breaking apart.

  • Customer: Kenneth from Friend NE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 6 of 7 people found this instruction helpful
It was very simple, pull off the old one, then I took some pliers and pulled out the fasteners. Took new gasket from bag and it just snapped into place.

Stove seal fell apart

  • Customer: Teresa from Washougal WA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 6 people found this instruction helpful
Removed old seal parts and had to cut new part to put into space but it went in without difficulty and has sealed the stove door tight again.

oven door gasket torn

  • Customer: Ovide N from Abbeville LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
ordered wrong part, called, was sent return number, sent part back, account credited ... easy return policy ... friendly people, good job

Gas manifold had holes in it.

  • Customer: Mr. J.C. from Haines City FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
Removed locking wire from bottom burner assembly then I pulled the element out and replaced with the new one.

Seal was fallinig off

  • Customer: Marilyn from Fresno CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
My husband did it. I was not there to see it. He said it took less than one minute, just snapped in and worked beautifully.

Bad Door Gasket.

  • Customer: Donald from Schuylkill Haven PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 4 of 6 people found this instruction helpful
First I took the new gasket out of the plastic bag to make sure it was the right size. Then I proceded to take the old gasket out by pulling it with a long noise pliers. Then I took the new gasket and went around the door putting the pins in the holes that, the old gasket was in. That,s about it.

I needed a broiler pan

  • Customer: Rhoda P. from Secaucus NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 7 people found this instruction helpful
I took the broiler pan out of the shipping container and put it in the oven.

Freont burners of both units had rusted though over the years of boilover.

  • Customer: Angelo W. from Chirfland FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
Lifted lid, removed old burner units, replace with new ones. In Less than two min. was back up and cooking.

Oven floor panel was warped.

  • Customer: Cindy from Colton CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
It was so easy, I pushed the panel towards the back and lifted the front up then lifted it right out. I am so glad that you had the part. I ordered it and when it got here, I just sliped it right in, perfect fit! Thank you so much! Cindy Brison

Racks were dark and dirty

  • Customer: Geraldine from Germantown NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 9 people found this instruction helpful
The first set of racks did not fit. I called the Service rep, gave him the model number and exchanged the racks for the new ones. The new ones fit perfectly and the service was excellent. I would definitely recommend PartSelect.com to anyone who wants to deal with a company with excellent service, parts and representatives who know their stuff.

Oven taking 30 mins to preheat and stinks like gas.

  • Customer: brian from granite falls WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
*Oven floor panel was blocked by fan guard.*

Had to remove fan guard first as I have the convection feature. Easy. 6 screws.

Replaced the oven floor panel, stained and warped.

Checked the ignitor switch by trying to preheat oven. Switch heats up but not enough to ignite gas.

Replaced the Ignitor. Easy. Plug and Play. Replacement insulation comes with the ignitor.

Thank You Parts Select. Youre my new favorite website. I can't wait until my next appliance breaks down.

My glass on the oven was broken.

  • Customer: Randy from Lufkin TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
All I needed was a phillips screwdriver to
take two screws out of the top panel. Then the two side panels pop off. Notice there are three click
tabs on each side panel, and also that the top and
bottom of the left and right panels, must be
manipulated in a sliding action(front to rear
facing the oven door front.) A good deal of
hand force is need to accomplish this.
Clean the old glass out, put the new glass in,
carefully might I add, and reverse the above
process. Just a little mechanical inclination
will get you there. Good luck!
I almost forgot to add that this job goes a lot
easier if before all of this, you simply remove the
oven door from the oven, by opening the door
about ten inches to the point where it stands
open on its own, then grasping it firmly on both sides and pulling up, with a slight jerking action.
This breaks it loose so it can very very easily be removed, and replaced. Best of luck!

class on oven door broke

  • Customer: andrew from haverhill MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
really eassy all you needed was a phillips screw driver
All Instructions for the 3100SPA
1-15 of 25