Models > 31000PAW Maytag > Instructions

31000PAW Magic Chef Range - Instructions

All installation instructions for 31000PAW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 31000PAW
46-58 of 58
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Used stove was missing 1 leg.

  • Customer: Clarence from Monroe WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
My used stove had been dropped by the previous owner. While I could live with the minor scratches on one side the wooden shims holding up one corner were annoying. A new leveling leg was less than $2. I used a pair of needle nose pliers to straighten the mounting hole and screwed the new leg in. This used stove was originally $2000 but I bought it for $999. the new leg plus shipping was about $10. What a deal.

Leveling legs were broken during the summer

  • Customer: Jayne from Willimantic CT
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
The range in my classroom had the leveling legs broke off by the summer staff. I ordered two new leveling legs and the night custodian replaced them in about 45 minutes and them leveled the stove. Parts were just as stated and easy to order.

Had to replace thermostat knob on an older Magic Chef oven. I The only knobs I could find locally ib hardware stores were useless. The adapter supplied with these kits was much too short about 1", needed about 3" to connect to knob.

  • Customer: Florence from Elmhurst NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I was pleasantly surprised that the knob I ordered from you was perfect. Your catalog picture/description was right on. I am so grateful I found your site. I looked @ others and they did not compare to your thorough description. Thank you.

Rubber seal was broken

  • Customer: Jennifer from Lynn MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Broke the same day I installed it

Oven knob was broken & stove was old

  • Customer: Janice from Springfield MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pushed the knob on to the part that was sticking out. Knob fit perfectly...had to use a substitute part & wasn't sure it was the right part, so was pleasantly surprised!

Oven temperture over 500 at any setting - thermostat

  • Customer: David from Suffield CT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Shut off the gas before you do anything! Remove the top front face cover by removing the four screws. Remove the three gas lines that go into the oven valve. remove the screws that hold down the manifold bar. Slide bar to the front and free from the burners and main valve. Remove the small bolt on the underside of the manifold that holds in the oven valve to the manifold. Remove old thermostat bulb from it's bracket inside the oven and pull through to the top of oven. Then remove the old valve. Remove rubber seals and transfer them to the new valve if you don't have new ones. Replace the new valve. Insert thermostat bulb on the end of the wire into the hole and down into the oven. Mount thermostat bulb into bracket. Then just reinstall in the same order that you took it apart. Then run the oven and check the new thermostat out to make sure it is working properly.

enamel on old panel was destroyed...

  • Customer: Lee from Truckee CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
take out the old, put in the new !.. wanted to do the same with the oven racks, but $100 for 2 seem to me as gouging, other than that = satisfied....great web site.... woody

Door seal was pulled out by grandson.

  • Customer: Michael P from Hickory Hills IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
finished removing door seal, used pliers to remove old securing studs. positioned new seal and pushed securing studs into existing holes and was done.

Numbers were wore off of the old knob so couldn't tell what temp the oven was on

  • Customer: Eleanor from Flat Rock MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed old knob and took new knob out of package and just slipped it on the stove. Less than a minute.

Thermostat Knob broke

  • Customer: James from Tallahassee FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I couldn't find my model number U31EA-7 so I decided to go with a deferent model number U31FA-7 Pulled the old Knob off and pushed the new knob on and it works great

As easy as it could be

  • Customer: Phillip from Twentynine Palms CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
I have worked in maintenance field most of my adult life and all aspects and to change the oven door gasket was no challenge what so ever. It took longer to find my needle nose pliers to remove the old gasket clips and then re-install the new gasket. Maybe 10 minutes total

Missing Oven Rack

  • Customer: Janine from Hatfield PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I think the installation instructions are fairly self explanatory. This is the second item I've ordered from Parts Select and I'm thrilled with their service. The items are always less expensive than other sites and they deliver what they promise. I would highly recommend them.

cracked and missing paerts of the seal

  • Customer: Cynthia from Petersburg IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Popped in there real quick. Wish I would have done it sooner, my oven heats up much faster.
All Instructions for the 31000PAW
46-58 of 58