Models > 31000PAW Maytag > Instructions

31000PAW Magic Chef Range - Instructions

All installation instructions for 31000PAW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 31000PAW
16-30 of 53
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

HAD TO CHANGE THE KNOB I COULD NOT READ IT

  • Customer: ANDREA from CORNING CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 4 people found this instruction helpful
PULLED THE OLD KNOB OFF AND PUT THE NEW ONE ON. ONLY THING THAT WAS DIFFICULT WAS MAKING SURE THE KNOB WAS THE RIGHT ONE BECAUSE THE INSTRUCTIONS KEPT LEADING ME BACK TO A DIFFERENT BRAND OF APPLIANCE BUT SINCE THE PHOTO LOOKED ALIKE I WENT AHEAD AND GOT IT.

Oven taking 30 mins to preheat and stinks like gas.

  • Customer: brian from granite falls WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
*Oven floor panel was blocked by fan guard.*

Had to remove fan guard first as I have the convection feature. Easy. 6 screws.

Replaced the oven floor panel, stained and warped.

Checked the ignitor switch by trying to preheat oven. Switch heats up but not enough to ignite gas.

Replaced the Ignitor. Easy. Plug and Play. Replacement insulation comes with the ignitor.

Thank You Parts Select. Youre my new favorite website. I can't wait until my next appliance breaks down.

Thermo Couple

  • Customer: Blaine from Oklahoma OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench set
  • 2 of 4 people found this instruction helpful
Removed old, install new

Drip pans were rusted. I had shopped for replacements at local appliance stores without finding them.

  • Customer: Norma J from Philadelphia PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Removed the rusted drip pans and replaced them with the new pans. Range looks great and ready for many more years of use!

Pilot light wood not light

  • Customer: Wiley from Leary GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench set
  • 1 of 2 people found this instruction helpful
Removed the top burner and the door on oven. Took out the bottom plate and the shield on top of the pilot light.

Old and corroded drip pans

  • Customer: Veronica from Miami Beach FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Furtunately, it was just a replacement of the drip pans. It changed the entite looks of my range for under $ 25.00 dollars. Very satisfied!

Racks were dark and dirty

  • Customer: Geraldine from Germantown NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 8 people found this instruction helpful
The first set of racks did not fit. I called the Service rep, gave him the model number and exchanged the racks for the new ones. The new ones fit perfectly and the service was excellent. I would definitely recommend PartSelect.com to anyone who wants to deal with a company with excellent service, parts and representatives who know their stuff.

floor panel heavily stained and warped

  • Customer: Joel from Monroe NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
slide latches in rear of floor panel forward and remove.

new knob

  • Customer: Marvin from Pahrump NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Pulled one knob off and pushed the other one on.

Pilot light would go out when oven was turned off but still allowed gas.

  • Customer: Steven from Oklahoma City OK
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set, Wrench(Adjustable)
  • 3 of 9 people found this instruction helpful
l removed the top section after the grates. Then l took the phillips screws out of the three brackets which hold the L brace which supports the controls,thermostat and the regulator. Only because l did not have a closed-end ratchet wrench for 1/4" and l could not locate my 1/4" socket for my small rachet. l disconnected all gas lines and the thermocouple, then l used the power screwdriver without the apex which makes it a great power 1/4" nutdriver and took out the two screws holding the thermostat. Then l just reversed all the steps installing the new thermostat and once l got the air out and gas was pure l lit the pilot lights and everything worked great. And l adjusted my top burner pilot lights a little higher to prevent them from gettig blown out so easy. Done deal.

Broken levelling leg

  • Customer: Linda from Oneida NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 4 people found this instruction helpful
Took the old levelling leg out and screw the new one in.

Temperature numbers were worn off the old oven knob

  • Customer: Rena from Cedar Rapids IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 4 people found this instruction helpful
I pulled the old knob off and popped the new one on! It was easy as pie!
The shipping was amazingly fast; I ordered the part on Easter Sunday and it was on my doorstep on Tuesday! Great service!

When I decided to do an extra cleaning of the rqnge, I removed the knobs, along with all the other parts and soaked them in the sink....I cleaned the knobs and set them up on the dish drainer to dry for a minute while I cleaned the rest of the stove...I dried the knobs, paced them back on the stove.

  • Customer: Betty from Nashua NH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
It was easy since it just pushes on...

The writing on the knobs was completely gone

  • Customer: Kalaine from Newark CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I pulled the knobs off and put the news one on. It couldn't have been easier. From my order to the fast shipping and helpful staff, I was completely happy.

PartSelect will be my first stop for all of my appliance repairs.

Thank you

I could not read the temperature ranges on my oven knob.

  • Customer: Debbie from Cincinnati OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Not much of a repair, just put the new one on. What I would like to share with you is the great ease of using Part Select Website. A stove knob you say? Well it seems like an easy part, but actually there a hundreds or more to select from. I could not find the model number on my stove. So I started looking through the site and it gave me options to choose from to narrow down the search. Being able to enlarge the part was extemely helpful, between 4 parts, I finally found the one that fit my stove. Might seem like not very much to you, but I was so happy that I finally found the part, it is the right part, and I don't have to mess with that stove thermometer anymore! The process was very easy, delivery was fast and I am one happy customer. Thanks Part Select! Debbie Watson
All Instructions for the 31000PAW
16-30 of 53