Models > 31000PAW > Instructions

31000PAW Magic Chef Range - Instructions

Installation Instructions for parts on models starting with 31000PAW

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

Models starting with 31000PAW

All Instructions for models starting with 31000PAW
1-15 of 58
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

PILOT LIGHT WON'T STAY LIT

  • Customer: Peter J from Brooklyn NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 20 of 23 people found this instruction helpful
First I removed the oven door by pulling straight up off of the hinges in the open postion.
Next remove oven racks,then use 1/4 nutdriver to remove back screws on inside oven bottom plate.Next remove gold nut on silver tube @ pilot connection,then remove 1/4 nuts that hold pilot assembly.Next open top of stove and remove small gold nut "with the thin wire from pilot"attached to the back left of oven control knob.Snake that nut and wire from the top of the stove down to the oven and removethe whole pilot assembly. To install Carefully unroll the new pilot assembly starting from the oven "There are two round holes you need to snake the tube into"and up behind the back & into the stove top. Make your connection@ the oven assembly.Next attach the assembly with the 1/4 screws that you removed,then make your connection"gold screw silver tube" Now push in your oven control knob to alllow gas to flow to the pilot tube and check for leaks with a water @ soap solution. No bubbles no leaks. Light your pilot ....you must hold in the oven knob. Put back in oven plate,,,, 1/4 screws,,,,racks close the stove top ,Put door back on hinges and your done.....HOPE I HELPED,..Pete

Oven rack lost in a garage fire

  • Customer: Bob from Saint Clair Shores MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 15 of 18 people found this instruction helpful
First I opened the door to the oven. Then I opened the box that the part came in. (knife) I then slid the oven rack out of the box and unwrapped the plastic, being careful not to bend or scratch the new rack. Now, this is the tricky part... I had to move the existing rack down one space to make room for the new one. Then carefully slid the new rack in, tipping it slightly and sliding it in. LOL

worn out door seal

  • Customer: Stella from Charlotte TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 13 of 14 people found this instruction helpful
removed old clips and remaining parts of old seal...new part already had clips attached, so just snapped them into holes in oven door.

Door Seal on oven was old, hard and breaking apart.

  • Customer: Kenneth from Friend NE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 7 of 8 people found this instruction helpful
It was very simple, pull off the old one, then I took some pliers and pulled out the fasteners. Took new gasket from bag and it just snapped into place.

Seal was fallinig off

  • Customer: Marilyn from Fresno CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
My husband did it. I was not there to see it. He said it took less than one minute, just snapped in and worked beautifully.

The oven part will not come on

  • Customer: Stephen from Syracuse NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Wrench(Adjustable)
  • 5 of 6 people found this instruction helpful
I did turn the gas off, then ,used my nutdriver,pliers and wrench{adjustable} to removed the old pilot and put the new one in.I turn
the gas back on and ignite with the lighter and it back on and it is working perfect.Thank you partselect.

Stove seal fell apart

  • Customer: Teresa from Washougal WA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 6 people found this instruction helpful
Removed old seal parts and had to cut new part to put into space but it went in without difficulty and has sealed the stove door tight again.

oven door gasket torn

  • Customer: Ovide N from Abbeville LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
ordered wrong part, called, was sent return number, sent part back, account credited ... easy return policy ... friendly people, good job

Bad Door Gasket.

  • Customer: Donald from Schuylkill Haven PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 4 of 6 people found this instruction helpful
First I took the new gasket out of the plastic bag to make sure it was the right size. Then I proceded to take the old gasket out by pulling it with a long noise pliers. Then I took the new gasket and went around the door putting the pins in the holes that, the old gasket was in. That,s about it.

HAD TO CHANGE THE KNOB I COULD NOT READ IT

  • Customer: ANDREA from CORNING CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 6 people found this instruction helpful
PULLED THE OLD KNOB OFF AND PUT THE NEW ONE ON. ONLY THING THAT WAS DIFFICULT WAS MAKING SURE THE KNOB WAS THE RIGHT ONE BECAUSE THE INSTRUCTIONS KEPT LEADING ME BACK TO A DIFFERENT BRAND OF APPLIANCE BUT SINCE THE PHOTO LOOKED ALIKE I WENT AHEAD AND GOT IT.

I needed a broiler pan

  • Customer: Rhoda P. from Secaucus NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 7 people found this instruction helpful
I took the broiler pan out of the shipping container and put it in the oven.

Oven floor panel was warped.

  • Customer: Cindy from Colton CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
It was so easy, I pushed the panel towards the back and lifted the front up then lifted it right out. I am so glad that you had the part. I ordered it and when it got here, I just sliped it right in, perfect fit! Thank you so much! Cindy Brison

original light grey color grates stained and unsightly--no amount of scrubbing or cleansers would make them look nice.

  • Customer: Linda from Jenison MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 10 people found this instruction helpful
Opened the box and took out the black color grates~~removed discolored grates and put the new ones on. Looks like a brand new stove and much nicer to look at as it is the first thing you see when you enter the kitchen.

Thermo Couple

  • Customer: Blaine from Oklahoma OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench set
  • 3 of 5 people found this instruction helpful
Removed old, install new

Racks were dark and dirty

  • Customer: Geraldine from Germantown NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 9 people found this instruction helpful
The first set of racks did not fit. I called the Service rep, gave him the model number and exchanged the racks for the new ones. The new ones fit perfectly and the service was excellent. I would definitely recommend PartSelect.com to anyone who wants to deal with a company with excellent service, parts and representatives who know their stuff.
All Instructions for models starting with 31000PAW
1-15 of 58