Models > 31-6758-66-03 > Instructions

31-6758-66-03 Frigidaire Range - Instructions

All installation instructions for 31-6758-66-03 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 31-6758-66-03
1-15 of 148
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

drawer glides were broke on front and back

  • Customer: bryan from sparta WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 462 of 463 people found this instruction helpful
used a screwdriver pushed the old ones out put the new in. the video instructions were great.

Front slide of bottom drawer broke off.

  • Customer: Jeanette from Alpharetta GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 460 of 461 people found this instruction helpful
Inserted new slide as directed by video. Very easy and video was very helpful.

broken slide

  • Customer: Joseph D. from Stuart FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 364 of 367 people found this instruction helpful
Pulled broken one out, slid in the new. Most unbeliveable service I have ever received. Tremndous job, you should sell it to others, Many thanks

rental property stove only had 2 working burners and bottom drawer off track

  • Customer: Steven from Taylors SC
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 313 of 316 people found this instruction helpful
first i took out burners then i took out the screws of the termnal block bracket. i then raised the lid on the stoveand clipped the wires on all 4 of the terminal block kits.i then slipped the shrink wrap on wires and used the wire nuts to connect wires together then heated the shrink wrap. I then put screws back in terminal block brackets. I then put the burners on while looking under lid so i would know they were making good connections as this is a bad design from factory. if you pull out burners to clean them and they are not put back in right you dont have a good connection and that causes the terminal blocks to get hot and melt. thats what happened in my case.
As far as the drawer glides they just snap into place

Bottom drawer broken

  • Customer: Michael from Middleton NH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 137 of 260 people found this instruction helpful
Frst I slid the drawer out.I then pryed the broken drawer glides off with a flat blade screwdriver. The new drawer glides then just snap into place,then reinstall the drawer and check for smooth operation.

drawer was tilting and wouldn't slide open easily.

  • Customer: jennifer from La Habra CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 67 of 68 people found this instruction helpful
The old glides were broken off so I didn't know I needed these glides until I saw the parts section of the Manuel. When they arrived I snapped them in with no effort at all.
P.S. The shipping is fantastic here......i ordered on Monday received them on Tuesday. Now that's shipping:>)

plastic clips were cracked.

  • Customer: EDWARD from ONSTED MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 66 of 68 people found this instruction helpful
It was so easy my wife did it bu snapping in the new clips.

Broke drawer glide

  • Customer: Tracy from Poulan GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 93 of 153 people found this instruction helpful
This was very simple I just snap the part on no tools required. it took less than 2 seconds.

Replacing Broken Parts

  • Customer: Scott from Noblesville IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 92 of 155 people found this instruction helpful
The two back door glides were missing and broken (one of each), and needed to be replaced. Finding the parts online was MUCH easier than I expected,and the repair was remarkably simple. Parts snapped into place, the drawer had to be lined up, and it slid right into place. Very easy!

drawer glide on bottom stove drawer broke

  • Customer: Homer from Thomaston GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 66 of 126 people found this instruction helpful
Snapped the new part into the slot the old one had been in.The repair including opening and closing the drawer took less than a minute.

Cord was not tightened enough by delivery crew.

  • Customer: Timothy from Spring Valley AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 26 of 47 people found this instruction helpful
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.

Oven light receptacle broken - bulb base broke off

  • Customer: Paul from Spokane Valley WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 17 of 21 people found this instruction helpful
Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven, and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.

missing oven racks

  • Customer: ALLAN from APACHE JUNCTION AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 12 of 12 people found this instruction helpful
order pcs fit perfect.

corroded terminals

  • Customer: Gary from hollywood FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 11 of 12 people found this instruction helpful
was more of a job of splicing wires together than anything else. Loved the heat shrink electrical tubing
to put over the wires for insulation. used a hair
dryer. must buy more of that amazing stuff

Broiler element burned out

  • Customer: louis from cuba NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 8 of 9 people found this instruction helpful
Remove old element by removing two screws on back wall of oven, pull attached wires out about 6" and disconnect. Reverse to install, very easy. Of course the oven door makes it harder to get at things, but it all worked out. Partselect was the only place I could find the element since the stove is 18 years old. I love keeping appliances going as long as possible.
All Instructions for the 31-6758-66-03
1-15 of 148