Models > 30-4980-32-02 > Instructions

30-4980-32-02 Frigidaire Range - Instructions

All installation instructions for 30-4980-32-02 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 30-4980-32-02
286-294 of 294
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven heated slowly, then not at all.

  • Customer: Gregg from Roseburg OR
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
1. First, I read other people's instructions on this site, and that helped quite a bit. My own model was attached somewhat differently, so I was unable to replace the igniter in the same fashion as others. 2. Turned off the power to the oven after having done the non-electrical work: removed cover plate from bottom of inside oven (two screws in the back) to expose the igniter, and the heat shield from underneath the oven once the oven drawer was removed. Old, old screws so that was a bit of rolling around on the floor. 3. After that it was fairly easy: turned off the breaker, snipped one igniter wire from a plastic harness assembly under the oven and the other from the electrical core underneath the oven which was attached with a clamp. 4. Removed two screws to release the igniter. Now I could work on it in the light. Stripped the old wire underneath the oven, attached the old clamp to the other new wire, and then clamped one wire on and joined the other to the plastic harness wire with the screw cap. It was a bit of effort merely to get at things, but not difficult. Breaker back on, and the oven now works perfectly.

Broken Drawer Glides

  • Customer: Rob from Ballwin MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Just like the helpful Video. Thanks.

Igniter was past-due for a change-out!

  • Customer: Kevin P. from Chanute KS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Just opened up the oven and went to work. Really easy repair. Removed floor of oven with two thumb screws. Removed flame diverter plate from burner with one screw. Removed igniter with two screws. Marked top wire, then untwisted old wire nuts to remove the old igniter. Replaced with new igniter and used enclosed new wire nuts. Reassembly was simply the reverse of above. Only issue - I needed longer arms to comfortably reach back into the oven!

Front glider ( plastic) on bottom oven drawer was proken.

  • Customer: CAROL from salt Lake City UT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I took the new plastic glider out of the bag and it took me about 2 minutes to fix the drawer!!! EASY!!!!! Thanks. carol

oven not heating

  • Customer: Mickey A from Linden MI
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Oven ignitor glowing but no flame . Tested ignitor w/ ohm meter reading 2.5ohms , should be 3.3 or higher to allow gas flow . Ordered new ignitor , replaces and jackpot !! Oven now fires and heats like new . Thanks for part . Cost , $50 instead of $150 .

there were no problems

  • Customer: Richard from Oak Lawn IL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
took off the front panel where the burner nobs are was very easy

The Ignitor had a brunt spot in the center.

  • Customer: Homer from Dayton OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I use a 1/4 in. socket and and ratchet to remove 2 screws and removed cover to get to sheild to unplug the two wire plug . Then used needle nose to remove two conectors from the gas valve.

Would not light.

  • Customer: John from Munster IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed oven racks. Removed oven bottom and flame diverter. removed two screws and cut wires. Spliced new wires and reassembled.

ice maker tray was leaking water from tray.

  • Customer: DALE from HAMBURG PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
i took 3 screws from ice maker,then unpluged from frig.i then transferred cable to new ice maker and installed back into freezer. very simple.
All Instructions for the 30-4980-32-02
286-294 of 294