30-3859-23-01 Tappan Range - Instructions

Removed the old oven racks and put in the new ones.

I actually read the first post, then ordered the part. The part showed up very quickly. I removed old part, attached new part with the ceramic wire nuts and put back together... Literally took 5 minutes and now works great...

replaced old part with new one and fixd the problem.

I followed past on-line repair reviews by prior customers, who problems were nearly identical to mine. It was basically an extremly easy repair. Those reviews/notes are great, leading to using partselect as a valuable start source for parts replacement. (I removed the part before ordering for assurance of getting the correct item. )

It took about 3 years to order and 3 minutes to fix. forgot to turn off "easy" video on conputor. Wife watched was mad........... for taking so long to fix. 41 years married, any video to fix wife and get me to 42 years as easy as changing draw glides? Thanks Jon

I called the repairman, and he said parts were no longer available for this appliance. He charged $85.00 for this advice. As soon as he left I looked on the internet and found your site and looked for the part. I found it right away, ordered it, and installed it. It was easy to install and it works great. The repairman candidly told me that new ovens are not near the quality as mine is and that is why I didn't want to buy a new oven. Thank you for providing an alernative to our throw-away society. Bill

The oven began to have low heat and then no heat. Read about it on-line and figured it was the igniter for the oven. Found the model number on stove/oven frame behind the bottom draw. Then I looked at a few on-line videos about how to install the piece. I have a convection oven and had to take the fan cover off to remove the bottom inside cover of the stove and I couldn't figure out how to remove the oven door to make it easier...so I had to leave the oven door on the stove. The stove door is heavy so be aware of that issue. Also I needed help...it was a two people operation. I needed to lay the stove on it's back to get to the piece. I needed to cut the wires and remember where everything went it was as simple as the video made it out to be...there were a few more wire connections. There is the issue of the door ...be careful you can stand the stove up and bring it down again but if not be careful/mindful of the door and it's weight and desire to slam closed...maybe a third person would be good to have around. ;) Anyway it can be done. Have patience. Take your time. Have a buddy to help you. Best part...the oven is now heating!! ;) Lovely!

After watching the videos on removing and replacing the front and rear glides on the bottom drawer, I was able to take the bottom drawer out, use a screwdriver to pry all the glides out of their slots and snap them all back in place in less than a minute. Without the videos I was completely helpless in knowing the sequences to performing this task.

disconnect electrical power to oven , removed face plate to where the igniter connections were. lift cover that is over the igniter in oven, remove igniter from burner, attach ner igniter to burner and route wires inside cavity where connections are. cut connector from old igniter leaving enough wire to splice to new igniter, strip wire and connect using wire nuts, put everything back together and test

first we went online to see if others had experienced the same problem, and what they did to fix it. ordered part to arrive within three days. husband removed connecters from old igniter and spliced them onto new one. We felt it should have come with connecters. set burner with new igniter in place, and it worked...Yay! just in time for Thanksgiving turkey!

Replaced the igniter.

The repair was easy.it took only minutes to install.The how to video was a big help.thank you parts select!

Unplug the stove from the wall socket. Remove the oven door as shown in the instructions for replacing the door. This makes the job a lot easier. At the rear of the bottom panel there is a screw at each corner. Remove these screws, a screwdriver will loosen them, then remove by hand. If you have a convection oven remove the fan cover as this prevents the bottom panel from coming out. There is a screw at the top and the bottom of the cover. You can then gently lift the bottom panel at the rear and work it out of the front lip. Install the new bottom panel in reverse order.

using socket set removed old ignitor,replace with new one and secured using the socket set. The oven lite right up.Service was A1. I ordered on Friday evening and the part was delivered on Monday. Thank you.

Inserted the new rear drawer glides