30-3859-23-01 Tappan Range - Instructions

I threw the old ones out and replaced them with the new ones. It was a no-brainer :) The parts arrived super fast. Great, no hassle service.

Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....

I went on line looked it up, ordered it, it came within 2 days.
I then removed 2 screws with a philips head screwdriver popped out old one, replaced with new one, put the screws in, turned it on , and it worked!
As a women I was thrilled to do this myself.

The front glides easily snap into a hole on the sides of the range. The rear glides easily snap onto the sides of the lower rear of the drawer.

Removed oven door. (Open to first position then lift the door straight up). Located igniter in bottom of oven, followed connecting wires to connection block below oven behind the oven drawer. Disconnected the existing wires. Lifted the burner out of oven to disconnect defective igniter. Screws were fused to the burner. Used vice grips to remove screws requiring the screw holes to be retapped. Bought new screws to replace trashed screws. Installed new igniter to the burner rail then set burner rail back in place. Fished the leads from new igniter back down to connector block. Reinstalled leads. Reinstalled oven door. Tested functionality of oven. Everything worked. Reinstalled metal plates back in oven. Reinstalled cover over connection block behind bottom drawer. Reinstalled drawer. With the exception of fighting with two screws fused to the burner rail it is a very straightforward repair and shouldn’t take much more than 1/2 hour.

Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)

First I turned off the circuit breaker to the oven. Then, I removed the base of the oven (the oven floor) by easily removing two screws. I also removed the flame guard by removing a screw. That easily exposed the old oven igniter. I removed the two small screws that held that in place. The igniter is connected by two wires, which you'll have to snip. Snip those very close to the igniter (leave about an inch of wire on the igniter). Using a wire stripper, remove about 1/2 inch of the outer sheath of the existing wires. On the new igniter, snip the wires leaving about 2 inches still connected to the igniter. Using the wire stippers, remove about 1/2 inch of the outer sheath. Using the plastic wire caps that came with the new igniter, connect the wires from the oven to the corresponding wire on the new igniter. Screw the new igniter back in place. Replace the flame guard and oven floor. Turn on the circuit breaker and start cooking again!

No installation steps required. I did have very fast delivery of parts ordered.

snapped the new piece of plastic in its place and ta da, its fixed.

The replacement racks were spot on and the service was outstanding. had the racks in 2 days. Happy Happy Joy Joy! :)

It was a replace racks not repair. No problem

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

Took the drawer out, snapped the new glide in place, and replaced the drawer. Installation was simple with no tools required.

My Tappan Tail:

Open the oven and remove the racks, turn on the oven light.
Remove two screws in the back to remove the bottom plate. Mine are about 1 1/4 in. long.
Remove one nut holding the butterfly plate in place. Ignitor will be exposed.

Turn off the oven light and unplug oven. Don't drop the plug behind the oven, I was ready for that one.
Drop light or flash light will be needed, it's dark in there. And something to sit on, 16" old plastic milk caddy, I just happen to have one.

Remove the two screws holding the ignitor, don't cut the wires just yet. Take note where the wiring runs. Install the new ignitor. My wires went behind the gas piping.

I cut the bottom wire from the old ignitor first, up close to the ceramic. Wire shield can be reused, slide it over the new wire. Cut the old wire, leave a lot. Trim the new wire to desired length and strip the ends of both and use the ceramic cap and connect the wires.
Do the top wire.
Slide the wire shield next to the igniter, adjust the wires so the wire shields won't slide away from ignitor. With the butterfly shield back in place it's time to plug it in and give it a test.
Nice.
Replace the bottom plate of oven, screw holes hard to find. Had to use an awl to find the holes to line up the screws. I also didn't push the front of the plate down into place until I had the screws started. It helped.

You might think this is overkill, but how many of us have ever replaced the ignitor. Not me.
I do a lot of DIY's. I'll rate this as a 1, easy.

What shall I bake first, cornbread of course. I my cast iron skillet.

get liquid wrench, remove oven door(2 screws) remove oven bottom(2 screws) follow directions included with part. unplug or shut off electricity at breaker panel, Have a good light source.