Models > 30-3649-23-05 > Instructions

30-3649-23-05 Frigidaire Range - Instructions

All installation instructions for 30-3649-23-05 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 30-3649-23-05
181-195 of 206
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven would not light

  • Customer: Edward from Pent Water MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Put a new ignighter in the oven I also would like to commend PartSelect for the fast service on the part i ordered it one day and recieved the part the nexted day i would recommend you any time

Oven lights intermittently, smell of gas

  • Customer: Robert from Lakewood NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Model# GLGF366ASD range
Turned off breaker
Removed oven door (see gas range manual for procedure)
Removed storage drawer on bottom of range.
Removed oven racks.
Removed oven bottom panel (2 screws in back of panel)
Removed oven shield (screw on left and right front of panel & nut in middle of panel)
At this point igniter was exposed
Removed igniter by removing the 2 self tapping screws securing igniter.
Note: threads on both screws stripped during removal, requiring both
screws to be cut off for removal.The stripping of threads of these screws
is probably normal due to the heating and cooling of the oven during
operation, making the threads on the screws brittle.
Marked the top wire on the igniter with a black sharpie
Cut both wires as close to the old igniter as possible.
Cut wires on new igniter about 10" long.
Connected new igniter with wire nuts (provided) making sure to connect wire from top of igniter to wire marked with sharpie.
Installed new igniter using 2 new #8x1/2" self tapping screws.
Pulled excess wire & wire nut connections down into the back of the storage drawer area making sure wires were resting on flanged area of panel.
Reinstalled oven shield, panel, racks, storage drawer, and oven door.
Turned breaker back on.
Oven works great.
Note: self tapping screws should be provided

Gas will not start

  • Customer: Paresh from La Palma CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I unplugged the range. Opened the range by removing the burners. Removed exiting spark module then installed new one. Just make sure the four plugs are correct.

Igniter not drawing enough volts to open safety valve.

  • Customer: Christopher from Oakmont PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the oven drip pan and removed the old igniter and cut wires and used the supplied wire nuts and replaced the old part turned the oven on and it ignited.

Just had to replace the racks in the stove.

  • Customer: charles from El Paso TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Did just want to comment on the customer service. It was great. The easiest to order that I have ever dealt with. Received prompt attention to the order and processing the same. JUST GREAT> Thanks

Gas oven light off time long, strong gas smell in house from long light off time. Oven would not control desired temperature.

  • Customer: Richard from Rockford IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Disconnected electric power. Removed oven floor and flame spreader to access igniter. Spliced replacement igniter to original igniter connector plug wires. Mounted new igniter and reinstalled flame spreader and oven floor. Reconnected electric power and checked oven operation. Oven light off time was within 1 minute and oven temperature controlled to all settings up to 450 degres.

Sliced Outlet Cord

  • Customer: William from Saint Clair Shores MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I was replacing a range oven hood, so I pulled the oven away from the wall but left it plugged in. I removed the old oven hood, which had an exhaust pipe that was still mounted through the cupboard. While I was preparing the new oven hood the exhaust pipe fell out of the cupboard and cut the oven wire in half. I was able to find the part number on the existing cord and looked up on line. I ordered the part using 3-5 business days and it showed up in 2 days. I was able to attach the new cord, which had an easy clip plug, and secure back to the stove. Very easy and very inexpensive to do.

Oven took a long time to light, did not stay lit

  • Customer: Carol from Campus IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Very Easy. Part arrived in less than 48 hours of ordering. Followed the directions included with part and referenced the information posted here.I have no mechanical talent and was able to install the part without difficulty.

Gas oven would not light

  • Customer: Steve from Fredericksburg VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I checked the igniter resistance with an ohm meter. It read about 350 ohms. Voltage across igniter leads with igniter removed was 120 volts when the oven temperature control was turned on, so I knew the gas control and thermostat were ok. The new igniter has a resistance of about 220 ohms, so the difference was apparently enough to keep the oven from turning on. This is the second igniter I've replaced in this 20 year old oven, the first bad igniter had open resistance, obviously since it was visibly cracked. The repair went very fast, directions were great.

would glow but would not ignite

  • Customer: charles from Mount Prospect IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Turned off power removed racks removed bottom panel removed flame distribution plate removed igniter i didn't use -the wire nuts 'the wires on the new part were more than long enough so i installed new stake ons reveresd disassembly process turned power back on and now it works great with a factory look

old oven racks were nasty!

  • Customer: Richard from Fort Wayne IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
We recently purchased condo and WhiteWestinghouse range needed some love. the old racks were not in very good shape so we ordered new.

oven would not maintain heat

  • Customer: Lauren from Delta Junction AK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
We took out the old thermostat and replaced it with the new one....now we don't have to buy a new oven!!!!!

no flame on broiler or oven

  • Customer: david from coalinga CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
replaced the ignitor switch, umplug oven turn off gas. removed racks unscrewed two screws in back of oven (inside of oven), removed bottom piece of oven, one screw for broiler cover removed, then two screws for ignitor, cut wires peeled off some excess covering, twisted the new ignitor to wires covered with attached cap tightly replaced two screws in ignitior, replaced one screw in broiler cover, two screws for bottom cover, replaced racks, pluged in turned gas and turned on stove ignitor lit up and started oven broiler, now i can cook again.

put the safty valve in

  • Customer: Donald from Conway SC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
turn the gas off unplugged it form electric removed the line took the flame plate off removed burner tube and the screw out with a nut driver that was all just put it back in reverse

Oven heated slowly, then not at all.

  • Customer: Gregg from Roseburg OR
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
1. First, I read other people's instructions on this site, and that helped quite a bit. My own model was attached somewhat differently, so I was unable to replace the igniter in the same fashion as others. 2. Turned off the power to the oven after having done the non-electrical work: removed cover plate from bottom of inside oven (two screws in the back) to expose the igniter, and the heat shield from underneath the oven once the oven drawer was removed. Old, old screws so that was a bit of rolling around on the floor. 3. After that it was fairly easy: turned off the breaker, snipped one igniter wire from a plastic harness assembly under the oven and the other from the electrical core underneath the oven which was attached with a clamp. 4. Removed two screws to release the igniter. Now I could work on it in the light. Stripped the old wire underneath the oven, attached the old clamp to the other new wire, and then clamped one wire on and joined the other to the plastic harness wire with the screw cap. It was a bit of effort merely to get at things, but not difficult. Breaker back on, and the oven now works perfectly.
All Instructions for the 30-3649-23-05
181-195 of 206