30-2272-00/07 Tappan Range - Instructions

First, I unplugged the oven from the wall. I opened the bottom drawer of the oven to see where the igniter was mounted, which was directly under the bottom pan of the oven itself. I opened the main oven door and unscrewed the 2 screws that were holding the pan to the bottom of the oven. Then, I slid the pan back towards the the back of the oven and it popped right out.

There were 2 hex screws that were holding the old igniter on, so I unscrewed them with my socket set. I made sure to pay attention to which wire was the top one and which one was the bottom one coming out the back of the igniter. I pulled off the wire nuts connecting the igniter wires to the wires of the oven. I striped the wires on the new igniter and re-attached them to the proper wires of the oven, using the included replacement ceramic wire nuts. I re-screwed the hex nuts in, mounting the new igniter to its proper place. I put the pan back and screwed the 2 screws back in to hold it in place.

Plugged it back in, turned it on, fired up within 20 seconds. Good as new.

It was very easy, The PartSelect company sent a detailed instruction sheet. I did not expect that! The sheet was completely detailed with everything I needed to do the job efficiently. They even gave a tool list for the job! I have bookmarked this company as my supplier for not only parts but very useful information in regards to appliance repair. I got more information from here than I could get from the repair guy at the appliance repair shop in town!!!I only had 1 day before Thanksgiving to get this done and WE HAD AN AWESOME TURKEY DINNER ON TIME AND DELICIOUS! I will be ordering again! Prompt service, correct parts, and a big bonus the instruction sheet with a tool list! AWESOME! GREAT COMPANY TO DEAL WITH!!! We will be ordering again!
THANKS MUCH for taking the stress out of a holiday!!! DAVID TAYLOR and FAMILY!!

First I disconnected all power sources. I removed the two clock buttons and the clock/timer switch from the front of the stove. I then removed the back panel from the stove by removing 4 screws holding the panel. This I found was not necessary. The clock was accessable from the front of the stove. This access from the back did allow me to do much needed cleaning from the back side. The front glass insert is held in place by 2 srews. After removing glass plate the clock is easily accessable. Removed two screws holding the clock in place, disconnected the two wires that supply the power to the clock, attached wires to the new clock, screwed the clock body back into the frame of the stove, and replaced the front glass panel.

Twisted replacement bulb into place easily. Let there be light!

Apparently, the original insulation had been removed due to a mouse infestation-the unit had been in storage for a while. After removing about 50 screws, I had all the body panels off and cleaned out the interior of the stove then installed the new insulation. I put it all back together and hooked it up- works just like new. I only paid 60 bucks for this oven, so all in all, not a bad deal.

Ordered new racks and replaced them.

Burner set screws froze up, was able to break 2 of 3 free and broke 3rd off. Used new simular screws to re- thread and fasten burner back in place. Bit of work but everything working. Used oppertunity to clean and re-level while I was at it. Everything good to go.

ordered received and placed it on the stove!! it was that easy!

The repair went relatively easy especially after reading that another homeowner found the door to be "spring loaded". I was prepared and made sure I held onto things tightly.I removed the screws as I came to them and carefully removed the other 3 pieces of glass, finally reaching the inner panel. Putting that in and holding it as I put the next piece back was the most difficult. Once that was in place, the rest was just a matter of redoing what I undid. Needless to say, I was a bit nervous the first time I used the oven. No problems though, works like a charm! Thanks!

First of all I would like to comment on how it easy it was to place this order and I was pleasantly surprised that it was rec'd the next day. Also it was the correct part that I needed. To install it, first I removed the screws and then the metal that was holding the broken glass. Once the broken glass was removed, I set the new glass in the metal strips and basically screwed it back together. Please note to be careful to remember which screws go where as they are not the same size and do not fit anywhere but where they belong. That was the only part of the job that I had a problem with.

Removed oven door. (Open to first position then lift the door straight up). Located igniter in bottom of oven, followed connecting wires to connection block below oven behind the oven drawer. Disconnected the existing wires. Lifted the burner out of oven to disconnect defective igniter. Screws were fused to the burner. Used vice grips to remove screws requiring the screw holes to be retapped. Bought new screws to replace trashed screws. Installed new igniter to the burner rail then set burner rail back in place. Fished the leads from new igniter back down to connector block. Reinstalled leads. Reinstalled oven door. Tested functionality of oven. Everything worked. Reinstalled metal plates back in oven. Reinstalled cover over connection block behind bottom drawer. Reinstalled drawer. With the exception of fighting with two screws fused to the burner rail it is a very straightforward repair and shouldn’t take much more than 1/2 hour.

If you intend to replace the igniter electrode ( part no. PS436633), purchase a minimum of twelve (12) top burner mounting screws ( part no. PS437925).

I also recommend that you replace all the electrodes since you have gone to the lengths described below to replace one igniter electrode.

After time, the heads of the mounting screws become brittle and break off when attempting to remove them with a 3/16" socket or nut driver.

Be aware that even the new screws are not exactly 3/16 hex, nor do they truly accept a 4.5 mm, or 5 mm socket. The 5 mm has to much slop, and the 4.5 mm, and 3/16" do not fully seat over the head.

First unplug the stove, and turn off the gas.

To remove the broken screws, I had to use a hand grinder to grind the heads off (you could be as careful as possible, but you will still damage the porcelain finish of the range top.) Unfortunately every screw has to be removed to lift the range top up enough to gain access to the electrode(s).

Along with the broken screws being in the burner casting, to replace the electrode, you have to remove the burner to work on it. Remove the insulated wire from the electrode, and then the gas line to the burner.

I recommend inspection of the insulated wires to see if they may be grounding out to the stove body. With the top removed and the burners still in place, plug the range back in. Turn any knob on (all electrodes should spark at the burner accept the bad one(s)). Observe the wires to see if there is sparking to the stove body. If there is none, continue to replacement instructions. If a wire is sparking to the body, wrap the damaged wire with HEAT RESISTANT tape. Standard vinyl electrical tape won't withstand the heat.

To remove the burner from the gas line, use a 1/2" open end wrench (preferably a tubing nut wrench) to remove the gas line along with an adjustable wrench to hold the burner to prevent damaging the gas line.

If your lucky, the cross point (Phillips head) screw that secures the electrode will remove without stripping, but don't count on it. I had to grind those screw heads off as well.

I used a size no. 30 cobalt drill in my drill press to attempt to remove the broken off screws, but because of the screw/drill size, I could not keep the bit on the hardened screw center, it kept walking off center. I ground the screws flush to the burner surface, used a center point drill, a center punch, and a spring loaded set point punch, nothing worked to keep the bit from wandering off center and into the soft metal casting.

I had to drill new holes with the no. 30 drill bit just to the right (or left) of the existing holes. Keep the same orientation and mounting distance when drilling, either to the right or to the left.

The new burner mounting screws did not work for mounting the electrode to the burning, I used small no. 6 self tapping screws to mount the new electrodes to the burner casting (the washer head was to large).

Reconnect the gas line(s) to the burner(s). It will be necessary to carefully bend the gas lines so as to line the new holes up with the top when remounting the burner(s).

If I had it to do over again, I would just donate the range as is, while explaining the problem to the donation center. After my experience, I personally don't think it is worth the trouble of replacing the electrodes on a range this old.

Hope this helps.

It went very well. Very quick. Just took out a couple of screws, took out the rest of the broken glass, slipped the new piece in and screwed it all back together. This was the first time I had ever tried to fix any part of a range/oven before, it was very simple...

I'll be happy to tell you "my repair story!" I was so happy to find a site that carried the knobs for my Tappan range. I called Sears, where we purchased the stove some 15 years ago, and was told that the only way to get new knobs from them was to purchase a "completely new unit" - or in other words, a new stove!!! With nothing being wrong with my stove, I began searching online for a site that sold knobs and found the PartSelect.com site. I was very happy with the service that I received, but thought that the stove knobs were grossly over priced!! I also thought that it was strange that you would send 1 knob at a time, but as long as I got them all, I'm happy. Thank you.

First I turned off the circuit breaker to the oven. Then, I removed the base of the oven (the oven floor) by easily removing two screws. I also removed the flame guard by removing a screw. That easily exposed the old oven igniter. I removed the two small screws that held that in place. The igniter is connected by two wires, which you'll have to snip. Snip those very close to the igniter (leave about an inch of wire on the igniter). Using a wire stripper, remove about 1/2 inch of the outer sheath of the existing wires. On the new igniter, snip the wires leaving about 2 inches still connected to the igniter. Using the wire stippers, remove about 1/2 inch of the outer sheath. Using the plastic wire caps that came with the new igniter, connect the wires from the oven to the corresponding wire on the new igniter. Screw the new igniter back in place. Replace the flame guard and oven floor. Turn on the circuit breaker and start cooking again!