2VGD29DQFW00 Whirlpool Refrigerator - Instructions

I followed instructions in the video you provided. No problem at all. Took less than an hour.

Just looked at your video twice and then did it with no problems. Thanks

I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent items in the fridge from being able to touch. Bad solution.

the part was very cheap and with the instructional video for replacement it was extremely easy to replace

Bracket pin that holds the water dispenser switch broke. Has to replace the whole bracket. Removed cover, unsnapped bracket, removed ice and water switches. Installed switches on new bracket, snapped in bracket, replaced cover. Ops check good. Very easy to do.

I had a problem with my ice dispenser not dispensing ice. The water worked fine but the ice side didn’t dispense ice. I watch the video on Parts Select.com and it was very helpful, but my model didn’t have screws to remove the front cover. At the bottom of the front cover was two indention where you could put a small tool and pry on it, I had to take a small pick tool and pry up on the front cover to pop it loose. You have to take something small like a pick tool because if you use something like a screwdriver or a butter knife you will get behind the plastic housing (also called a hood) that is screwed to the refrigerator. The key is to remove the face plate from the plastic hood piece (that is screwed to the refrigerator), so you have to get in between the face plate and the plastic housing. If you get behind the plastic housing you can break the housing, you must get between the two pieces and it will pop loose. This is the only problem I had with this installation. The rest of the repair was very easy and now my ice maker dispenses ice great.

Took old one out put new one in and its like new! Costs for a simple drawer was $75! Expensive but the transaction was simple!

Replacing the door closing cams, starts with emptying the door of all foodstuffs. Remove upper hinge cover. While supporting the door, remove three upper hinge screws with the nutdriver. Lift upper hinge from top and lift door off lower hinge pin. Remove the cam retaining screws on both the bottom of the door and the lower hinge pin. Pry (if needed) the worn cams from their position. Install new cams making sure to line up the screw holes. Re-install screws, tightening just snug. Lift door back onto lower hinge pin. Set upper hinge back in place with screws loosely installed. Check door gap, top to bottom to ensure proper alignment. Tighten upper hinge screws and re-install hinge cover. Check door for proper function.

I've replaced the door cams in the past, but they didn't last very long. I finally realized on my own that both parts need to be replaced at the same time. One piece is on the case-side of the bottom hinge and the mate is on the door-side of the bottom hinge. They both have a ramp shape, with door ramp riding up the hinge ramp as you open the door. The ramp shape makes the door want to slide back down the ramp to close automatically. These are plastic parts that wear out over time. If you don't replace both at the same time, the ramp shapes don't match and they wear out quickly. They are inexpensive parts, so always replace both at the same time. I added a thin layer of petroleum jelly to help them glide better. Hopefully this fix will last a long time. It's extremely easy. First take off the top hinge of the door. Then lift the whole door off the bottom hinge. You can set it on a chair with the bottom hinge hanging over the edge of the chair. Replace the two parts, one on the door bottom hinge and one on the refrigerator case bottom hinge. Easy as pie. The only tool needed is a nut driver. You need a helper to help lift and balance the door while you work on it.

took out the old one and replaced with new. PERFECT FIT.

repair went well. Ice maker still not making ice. UGH

First I used some glue to stop the crack from spreading, and that worked for a while, but then I deceided to get a new replacement part. What I got was better than the original one as it had a white protective piece over the end of the drawer and I believe that will give more protection to the drawer. My kids did not always close the drawer all the ways and that is how the crack started. So now the refrigerator looks like new again.

part better than original just unscrewed and removed original. new one fit just right.

Set out an area large enough to lay the door down once I took it off the refrigerator. Took off the top screws and hinge. Had my 12 year old so help me with the door and hand me all the tools so I could quickly change out the parts and not leave the Refrigerator open for too long. I think from the moment we took the door off to the moment it was back on was probably about 5-6 minutes tops. That is how easy this was. All the parts fit and thank you to PartSelect and it great website that advised me of the second part that went with the first if not I would never have known. Thanks again!!

We were afraid of breaking the new part.But after watching the repair video about how much pressure to apply the part snapped right in. Thamk you for the video it helped alot.found the part quick and easy and it was shipped fast to us problem solved.