2LSR5233BQ2 Whirlpool Washer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
agitator not move
I order the repaired kit and I use the old part where the dog cam goes due to the new one is loose.
Parts Used:
-
Nelson from Silversprings, MD
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Agitator cogs replaced
Exactly as described in the sample video on your site.
Parts Used:
-
Scott from Mooresville, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Slow agitator
Half inch ratchet extension unscrew remove replace cogs reinstall retainer ring drop back in . Watch how fast agitator spins.
Parts Used:
-
Steven from Aurora, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Top half of agitator "Free Wheeling"
I viewed the repair video provided and then dove into the project. I am sorry to say that the time suggested for the fix was a bit misleading. Took me less than five minutes rather than the fifteen minutes suggested. Thanks Parts Select for a great assistance in saving me an expensive repair call!
Parts Used:
-
Paul from Maple, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Top part of agitator was inoperative
I looked at the video that was available for a general idea. I knew the exchange was fairly simple but it never hurts to watch someone else explain it. Used my socket and extension, some lube as recommended, replaced the pieces, tightened and turned the washer on. Worked like a charm. Thanks
Parts Used:
-
William from Springfield, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
would not agitate
watched a utube vidieo and followed directions in repair kit poped the cap removed screw seperated agitator replaced worn parts reasembeled agitator simple
Parts Used:
-
Rick from Galva, KS
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Slow spin cycle.
Found Website and entered model number. Used the quick explanation of problem to find required parts for repair. Found that one washer was left off in the parts recommended for repair while repairing that was purchased locally because it was cost was lower than part and shipping on line. The parts ordered from Part Select arrived with in 3 working days. Video was very helpful for the whole repair.
Parts Used:
-
Stephen from Hernando, MS
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
no spinning agitator in top portion.
took broken agitator dogs out and put new parts in, it was very easy repair.
Parts Used:
-
jung from river vale, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
A Good Fit
The most difficult part was aligning the two sides of the coupling. Disassembling the motor from the transmission was a snap. The replacement coupling was of higher quality than the original. It had metal bushings in the center holes, where they interface each driveshaft. The original did not. It was plastic.
Parts Used:
-
Ernest from South Windsor, CT
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
top 1/2 of the agitator would not agitate
exactly like the instructions that came with the new parts said. they were very accurate.
Parts Used:
-
ROBERT from UNION, IA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Socket set
Was this instruction helpful to you?
Thank you for voting!
metal reinforced coupling
The repair went very well as per the video, however the metal reinforced coupling only went onto the shaft half way. To ensure the coupling was flush with the top of the shaft I has to use a hammer and tamp the coupling onto the shafts. If you left it halfway on the shafts there was no room for the rubber spacer between the couplings. Other wise it operates very well.
Parts Used:
-
Sammy from Strawberry, AZ
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
agitator ears slipping
we took bolt out then agitator came apart it was so easy with the how to video we had it done in about 20 min. thank you
Parts Used:
-
john from gallipolis ferry, WV
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
broken seal
-
Lorraine from Millsboro, DE
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Agitator was not working right
-
Barbara from Woodland Park, CO
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
last sicle
-
jose from South Sanfrancisco, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!