Models > 2DMTW5705TW0

2DMTW5705TW0 Washer - Overview

Parts and Repair Help for models starting with 2DMTW5705TW0

If you know the washer repair part you need, you can browse the list of all parts for models starting with 2DMTW5705TW0, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for 2DMTW5705TW0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Models starting with 2DMTW5705TW0

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.46

Agitator Directional Cogs

These agitator directional cogs are commonly referred to as dog ears. They come four to a package and are usually used with direct drive washing machines.

$18.81

Agitator Repair Kit

The agitator kit is most commonly used if the top part of the agitator is not moving correctly but the bottom is. This kit now includes all pieces shown in photo plus the thrust spacer, inner cap seal and agitator bolt washer. May need agitator grease for repair.

$29.85

Direct Drive Water Pump

It is intended for use with washing machines that do not have belts. This drain pump has two ports for water to pass through: a large one, and a smaller one.

$2.67

Suspension Spring

Sold Individually. Appliance takes 3 of this part.

$43.96

Clutch Assembly

A worn clutch can cause a slower spin speed which will leave your clothes wet after a cycle. This clutch assembly comes with brake cam driver, blue spring for large capacity wash...

$2.88

Inner Cap Seal

Also known as an O-Ring.

$2.64

Thrust Spacer

This white thrust spacer is made of plastic and is also commonly referred to as a retainer ring. It is used in the agitator assembly of many direct drive washing machine models. Th...

$4.46

Agitator Bolt

This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".

$21.75

Lid Switch

The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed. This part includes the grounding wire.

$3.96

Tub Spring

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water pump leaking when machine used.

  • Customer: Tom from Granby MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 374 of 389 people found this instruction helpful
The hardest part of this job was pulling the machine away from the wall so the hoses could be disconnected and the machine flipped onto it's back. Putting the machine on it's back does two things. It drains the water left in the bottom of the tub so it won't pour out onto the motor when the old pump is removed, and gives the necessary access to the pump. ... read more

top half of agitator did not move during wash cycle

  • Customer: dennis from new stanton PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 168 of 190 people found this instruction helpful
pull off softner dispenser, pop off agitator cap by inserting straight screw driver into small slot, remove bolt inside agitator with socket wrench and long extension, pull agitator straight up off shaft, place agitator on floor, with feet holding bottom half pull top half apart from bottom half by pulling straight up, note direction of old cogs remove and r... read more

spin cycle did not engage

  • Customer: Andrew from SLC UT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 156 of 168 people found this instruction helpful
researched potential causes, found cluch dust under the washer and determined that it wouldn't engage because clutch was too worn. ordered the assembly, removed agitator from inside the tub as it is connected to the gear shaft, turned washer on it's back for access to motor, unattached the direct drive water pump from the motor drive, unbolted the 3 gearcase... read more