2DLSQ8000JQ5 Whirlpool Washer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
pump leaking
Unscrewed and flipped back control panel. Unplugged lid switch and removed fron/side/lid sheet metal. Disconnected hoses from the pump, removed pump retaining clips and switched to new pump. Reversed procedure, plugged machine back in and everything worked like new. There was no need to lay the machine on it's back as instructed by the video. It would helped pins that hold the sides in place (at bottom rear) where about an inch taller.
Parts Used:
-
David from Erlanger, KY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
failure of agitation and spin, pump works
According to the video on your site with adaptation to the exact model. More time spent in removing/replacing the cover than any other part of the job
Parts Used:
-
Max from Redmond, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
my washer would not agitate
simply take the old agitater out and put the new one in. agitates great now.
Parts Used:
-
Ann from Stafford Springs, CT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
pump leaking
Tipped washer on to front. Popped off retaining clips. Pulled off old pump and put new one on without tools. Needed pliers to remove hose clamps. Then put retainer clips on by hand. Job done washer works great.
Parts Used:
-
Greg from Davenport, IA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
broken coupler between motor and transmission
-
gregorio from suamico, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
plastic part of coupling was broken
The new coupling parts are better made than the original parts. It was difficult to disassemble motor unit to get at the the old coupling, but once that was accomplished, the new coupling installed pretty easily. The machine is working fine now.
Parts Used:
-
Judith from Concrete, WA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Socket set, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
drip of water inside tub
Shut off the water and disconnect the water Hoses Unscrewed the header from the back slide it forward take out the retaining clips with screwdriver, tilt cabinet forward and move it aside unscrew the inlet valve from the back frame of washer replace it with new one, bring cabinet back in place and just back track what you did from here on
Parts Used:
-
John from Ramseur, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Severe water leak.
Laid machine on side, removed pump (stubborn),installed new pump. Set back up. Worked great.
Parts Used:
-
Robert from Chester, SC
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
spin cycle did not engage
researched potential causes, found clutch dust under the washer and determined that it wouldn't engage because clutch was too worn. ordered the assembly,It was very easy to install. I also noticed oil residue on the side of the washer so after more research I found out I needed to replace the transmission also. The seal on top of the unit was worn out. I ordered a new transmission and install it and now it works like new. It's very rewarding to fix your own washer. Now all my friends are fixing their own washer and dryers. Thank You!!!
Parts Used:
-
Lamar from Rochester, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Was this instruction helpful to you?
Thank you for voting!
Top agitator not working
-
Carson from Corbin, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
agitator cogs were worn
-
dave from delphi, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Socket set
Was this instruction helpful to you?
Thank you for voting!
top agitator quit agitating
Well,the repair was actually easy once I read all instructions. My son and I did the repair. After we got the agitator apart my son took his feet(after I told him thats how you get it apart)to separate the bottom agitator from the top agitator. Everything went everywhere. Thank god for Part-Select and their wonderful pictures. We put everything back together and it is working like a brand new machine. THANK-YOU. If we would of read first it would of only took 15 minutes to install. S Brazil
Parts Used:
-
Sylvia from Alamogordo, NM
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Agitator was not working properly, would barely spin.
The whole process took about 20 minutes. I popped the cover off the top of the Agitator and unloosened the nut holding the agitator onto the shaft. I then replaced the cogs, which just slipped into place. Finally I replaced the agitator back onto the shaft and tightened the nut and replaced the cap.
Parts Used:
-
Edward from Andover, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Fabric Softener Dispenser won't dispense softerner.
-
Rennel J from Rosamond, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Will not agitate
-
Scott from Corbin, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!