Models > 28FN-6CXWV8-DZ > Instructions

28FN-6CXWV8-DZ Magic Chef Range - Instructions

All installation instructions for 28FN-6CXWV8-DZ parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 28FN-6CXWV8-DZ
1-15 of 109
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Drip bowls were burned and tacky

  • Customer: Donna from Dallas TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 459 of 458 people found this instruction helpful
First I removed the old bowls and replaced them with the new.

Drip bowls needed to be replaced

  • Customer: John from Chester VT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 444 of 523 people found this instruction helpful
took old bowls out, put new bowls in, took a coffee break

Old drip pans stained

  • Customer: Linda from Atlanta GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 210 of 412 people found this instruction helpful
Replaced old drip pans with new ones - very easy - even a 68 yr old lady can do it!!

Stove top element not working due to bad receptacle.

  • Customer: Richard from Carthage NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 93 of 102 people found this instruction helpful
Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit.
My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com.

one of my burners would only work half the time, and you had to wobble it to make it work

  • Customer: cindy from Sebeka MN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 128 of 249 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, connected the new element using the wire caps, and finished bye rescrewing the element backinto place.

We needed new drip pans and no one carried the model we needed

  • Customer: sylvia from ventnor city NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 65 of 65 people found this instruction helpful
we removed the old pans after first removing the electric heating element and simply inserted tne new pans

Inner Oven Glass broken

  • Customer: David from Wayne NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 19 of 24 people found this instruction helpful
I removed two retainer screws which released the outside panel.
Next I removed 2 screws which hold the middle glass pane from one of its retainer brackets.
The was another panel with 4 screws to remove before reaching the final glass inner assembly.
Once that panel was reoved with the broken glass it was time to put the repacement glass assembly back together.

Burned terminal block and filter board

  • Customer: Joseph from Decatur GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set
  • 26 of 52 people found this instruction helpful
Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.

Element burned out

  • Customer: Anita from Hudson CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 15 of 23 people found this instruction helpful
Unplug Stove removed screws pulled out
element. Lifted off the wires with a pliers they slid
onto the element ends that were pointed up
was very easy.

Burned out light bulbs in microwave hood stove

  • Customer: Herbert from Norton MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 10 of 12 people found this instruction helpful
I had some difficulty removing the glass plate because of the awkward (upside down) position of the screw that retained it. After replacing the burned out bulbs and replacig the glass plate the problem of replacing the screw involved my dropping the thing several times before I got the screw threads to catch. I got a screw thread to catch enough to hold the glass plate in position and left it at that.

burned out bulb

  • Customer: john from plainfield IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 13 people found this instruction helpful
removed two screws,lowered the glass shield,removed the burned out bulb and replaced it with the new one. I ordered the bulb from parts select and recieved it two days later. It was a pleasure to deal with them, and certainly use them again.

oven door spring broke and had to be replaced, oven light out and had to be replaced

  • Customer: Ed from Anderson IN
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 10 people found this instruction helpful
The old gasket fell apart as I replaced the oven light and had to be replaced. That was very easy once I received the part. The spring broke on the oven door and had to be replaced. I initially tried to reach in from inside the pan drawer under the oven. That was impossible to reaach but it only took a few minutes to realize that I had to remove the side panel. I had to slide the range out from between the cabinets, but once that was done it was a relatively easy fix, without any special tools needed.

spring broke on one side of door hinge

  • Customer: Travis from Lexington OK
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 7 people found this instruction helpful
Pulled the stove out, removed the sides and attatched the new springs( replaced both while the stove was out). Worked like new and put the stove back.

BLOWN FUSE - PS1750182

  • Customer: John from Inverness FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
UNSCREWED THE COVER OF THE MICROWAVE REPLACED THE BLOWN FUSE WITH THE NEW FUSE, PLUGGED IN THE MICROWAVE AND TESTED ALL FUNCTIONS AND EVERYTHING WORKED FINE.

THX FOR QUICK DELIVERY.

Burner was out but the burner coil worked on onother burner

  • Customer: Richard from Orange CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 5 people found this instruction helpful
Replaced receptacle but it was not the problem. After further inspection I believe that the problem is the switch. The switch is on order now from Part Select.
All Instructions for the 28FN-6CXWV8-DZ
1-15 of 109