The manufacturer-approved Ratchet Pawl (Starter Pawl) comes in a set of two (2). This part attaches inside the recoil assembly, and is used to engage the flywheel. if broken due to wear/damage it will...
$3.99
In Stock
Order within the next 7 hrs and your part ships today!
This OEM Gasket Rocker Cover, which can also be called the Valve Cover Gasket, is used to provide a seal between the valve cover and engine. This is a gray-colored part, measuring 5 1/2 x 4 Inch, and ...
This OEM Seal-Oil (PTO Side), also called the Oil Seal, is a Black, Nitrile Rubber, 2/14 O.D., individually sold part which is installed using a Seal Puller. Customers rate the installation difficulty...
$7.88
In Stock
Order within the next 7 hrs and your part ships today!
The Oil Seal is a manufacturer-approved rubber part which provides a seal between the crankcase and crankshaft by attaching around the axle shaft on the crankhouse housing. Installation is rated as "M...
$6.59
In Stock
Order within the next 7 hrs and your part ships today!
This OEM exhaust gasket in lawn and garden equipment creates a seal between the engine block and the muffler or exhaust pipe so that exhaust gases do not leak. This is 3.30cm in diameter and 6.35cm in...
$5.71
In Stock
Order within the next 7 hrs and your part ships today!
The Seal-O Ring, also known as the gasket, is red in color, made of rubber, and is an OEM part that requires some skill to replace. This part is designed to create a seal between the carburator and ma...
$4.99
In Stock
Order within the next 7 hrs and your part ships today!
Order within the next 7 hrs and your part ships today!
Questions And Answers for 280H07-0119-E1
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
1 question answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Kim
May 10, 2023
need a starter , spark plug and solenoid for 2t1232 gravely zero turn model#915030 serial # 010337 12hp briggs and stratton
For model number 280H07-0119-E1
Hi Kim, thank you for asking. The parts you are looking for are the spark plug, part number PS9281094, the starter motor, part number PS11829347, the rewind starter, part number PS9983435, and the fuel solenoid, part number PS9076225. We hope this information is useful!
No compression. Removed the cylinder head. freed the screw, checked the valve to see if it still sealed. Turned the head over with the valves in it, install a spark plug, fill the head dome with gas and see if any leeks out over a 2 hr period. If not you are good to go. Reinstalled every thing with new gaskets and a new carburetor screw.
... Read moreSet the valves to spec. Complete the rebuild and there you have it. Rebuild the carburetor while you have it apart. This motor runs great !!!
I went to Troy-Bilt first first for the part-nothing, then B&S engine, still no help surfing their websites for this part. Again, no help. Before giving up completely I thought about all the parts I have bought from PartSelect for washers and such. Typed in "Fan-Flywheel" B&S. First thing that popped up was a picture of this part. All my
... Read more searching on Troy-Bilt mower site and B&S site for over two hours with no results, and then I go to PartSelect and without my model number or anything else, they had it and even displayed my model number and sent it right away, popped it in and the mower is working fine as ever. No matter what you need, I say save yourself a lot of time and just go here first. I'm a loyal member of PartSelect for over six years!!!
First I opened the top of the mower to expose the housing cover. Secondly I removed the four housing bolts to remove the housing cover from the mower. Next I removed the tube breather and installed the new tube breather and replaced the housing cover with the four bolts previously removed and closed the top of the mower. I filled the mow
... Read moreer with gas to check for leaks which weren't any leaks. I proceeded to mow the lawn with ease.