2599CIWEW Amana Refrigerator - Instructions

I removed the ice maker, which consist of three 1/4 inch screws to install the water fill cup and bearing. One must loosen the front panel of ice maker to install the fill cup which consist of two standard screws, slide forward enough to install new fill cup. The removal of the Icemaker control was simple, using #2 phillips screwdriver and three screws. Unplug the control and install the new one, replace the three screws and cover. Reinstall the ice maker and within one hour cubes were dropping in the bin. I saved a lot of money repairing myself, which more than covers the shipping cost. Shipping was fast, two days.

Repaired by following the video with ease and was happy to see ice the next morning.Great service, price and advise .Thank you.

follow instructions on web site to install motor module.Great web site. Saved me a lot of money.

Watched the video on the web site and then followed the instructions. It was very easy to change. After changing it, I filled it with water from a cup to get it started making ice since the video does not address how to do this. It has been working well ever since. If you are handy with tools, you can do this.

I put in a new ice maker because it was not in very good condition. The water valve had a very slow leak which allowed water to freeze on the way to the ice maker and plugged the line. This problem was in one of your repair articles all of which were very welcome

A local appliance parts distributor suggested that I go on line to get help figuring out the problem. The motor assembly was 51% probability. I ordered the part and followed the instructions given at the time of purchase. In a very short time ice was dropping.

Just watch video from part select and following the instruction to replace the control and motor assembly.

I had to replace the whole unit. The tray should have lasted longer and there should have been a replacement tray available.The installation was easy. 3 screws removed, unplug unit, turn off water and put in new unit.

I removed the ice maker unit completely from the freezer, following a Utube repair video that I found. I originally thought it was just the control board that was defective, because on examination, found a burned-out copper trace on the board, as well as a burned-out plastic connection point. Installing the new parts was a breeze. This icemaker is pretty foolproof, with plastic tabs that line up with the housing. a matter of lining up the screw holes was all that was necessary. Only problem I had was attaching a plastic cover that shields the electrical connection from the water. Once all was installed, I had to wait overnight for the icemaker to make ice. We've had ice ever since! Thank you Partsselect for very courteous and fast service!

There are two tabs that hold the icemaker to the rails it sits on. I use a small screwdriver and pushed the tabs up to release the tray and slid the Ice maker out. the cover over the control motor just pops right off. Then I removed three screws from the control motor pulled it off and put the new on, replaced the screws and put the cover back on and slid the icemaker back into the rails. I shut the freezer door and within the five minutes it took me to put my tools back in the garage, it was dumping ice. Very easy to fix. You do not need to remove the screws that hold the icemaker to the tray.

removedicemaker and unscrewed 3 screws hill ding motor assembly and control module to ice maker . nstalled new part and attached it with the 3screws. reinstalled ice maker and ice making cycle began almost immediately.

Removed ice maker and installed new part

Turned off the icemaker and took out the hex screw at the back of the unit that held the cable guard. The ice maker was easy to slide out after releasing guide locks on each side of the unit. Pulled the unit forward and released the electrical connection. With the unit on the cabinet, I removed the motor housing cover. Took out the 3 scews holding it in place and the old motor was out. Just reverse the steps putting the new one in. In an hour or two we heard ice dumping into the holder.

Removed icemaker, replaced motor and reinstalled. Very quick delivery of parts, fit perfectly.

replaced the motor control assembly and it works great