Models > 25380 > Instructions

25380 Kenmore - Instructions

Installation Instructions for parts on models starting with 25380

These instructions have been submitted by other PartSelect customers and can help guide you through the repair with useful information like difficulty of repair, length of repair, tools needed, and more.

Models starting with 25380

All Instructions for models starting with 25380
1-15 of 22
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken ice maker

  • Customer: Juan from Miami FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 35 of 50 people found this instruction helpful
Unplugged faulty ice maker, removed two screws holding it to the refrigerator and took it out. Reversed the operation with the new ice maker and after a few minutes presto, we have ice.

Ice maker stopped producing ice

  • Customer: Jeremy from Peoria AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 15 of 23 people found this instruction helpful
First I removed ice maker and tested the micro switches and motor individually. Then checked the resistance of the heater element, and the thermostat. All components tested okay and worked individually. However when installed in the freezer the motor would not turn. and if you manually turned the gear in front, which should cycle everything,nothing would happen. Finally, I found one part that I had not checked, the thermal cut-off, and upon removing it, one wire fell off the small square piece. This wire was corroded. I replaced the unit in about 10 minuites and ice maker is working perfectly again.

Was not filling the ice tray full.

  • Customer: Orville from Garland TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 14 of 22 people found this instruction helpful
I had put in a new ice maker and it still had the problem, (I needed the Ice maker anyway) I installed the vale and while I was at it I put a five year filter on the water line that went from the value to the Ice maker, it took less than one hours, the ice is making like it did when it was new, I could not be more please at theis time. Thanks for your Interest. God bless.

ice maker would not make ice

  • Customer: paul from traer IA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 9 of 14 people found this instruction helpful
un plug fridge. removed ice maker from fridge. loosen 2 mounting screws. lift unit in slots to get over heads of screws. unplug wire harness. remove cover. remove 3 screws from control housing. remove 2 motor mounting screws. unplug motor wires from switches w/needle nose. installation is the reverse. plug in fridge turn on icemaker. takes 10 to 15 min to start to cycle.
easy and cheaper than new fridge or ice maker

Ice Maker Repair

  • Customer: Kristi from Winfield WV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 6 of 8 people found this instruction helpful
The ice maker wouldn't fill with water. The maker itself appeared to operate but the tray would not fill. I ordered the part from PartSelect.com. The website allowed me to conveniently match a picture of the part with my part on the refrig. I ordered the part and it arrived in two days. I was impressed!

I turned the water to the ice maker off, unplugged the refrig. and pulled it out from the wall. I loosened and removed two screws with a nut-driver and unplug the wiring connection from the old part by simply pulling on it with my fingers. I then unscrewed the water connection from the old part using a set of pliers. The old part was then discarded. I connected the water and electrical and remounted the new part using the two screws. It was too easy!

WATER WAS NOT BEING SENT UP TO ICE MAKER

  • Customer: BARBARA from DIAMOND IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 13 people found this instruction helpful
I REMOVED A COUPLE OF SCREWS FROM THE OLD PART, AND INSERTED THE NEW PART. REPLACED THE SCREWS AND I WAS DONE.
NO PROBLEM. I'M AN ALMOST 60 YEAR OLD WOMAN, AND FIXED THIS MYSELF. IT WAS SO EASY.

Ice maker stopped working

  • Customer: Fred from Las Vegas NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 3 of 6 people found this instruction helpful
Took off old part and installed new part

Warter valvr cracked

  • Customer: Louis from Damascus PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 2 of 5 people found this instruction helpful
It was real easy but I still have problem making ice cubs
Fell problem is in the ice maker went it dose make cubs they don,t dump

After installing new ice maker water was not running into the ice maker.

  • Customer: Leah from Tecumseh OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 2 people found this instruction helpful
Shut off water supply under the sink. Removed old valve and installed new valve. Turned water back on and within a couple hours the first batch of ice made.

Water Valve was leaking water and not making ice

  • Customer: timothy from georgetown TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 4 of 15 people found this instruction helpful
I unplugged the fridge and unscrewed the back cover,unscrewwd the two screws holding the water valve in place and the water line to the ice maker and the electrical connection and install the new water valve,then buttoned everything back up and plugged the fridge back in and it is working great,making ice as normal.

Ice cubes were half the normal size to none at all

  • Customer: Gaylord from Riverside CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Remove back cover (5 screws )remove valve ( 1 screw ).Disconnect in and out water lines. Disconnect wire on solenoid. Install in reverse. Dont forget to turn off water.

arm wouldn't go all the way down and dump ice

  • Customer: Ronald from Ft. Myers Beach FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took front off and found the broken spring, got new one and replaced, now works great. Make sure to unplug as the water can come on and flood the freezer.

valve busted

  • Customer: Kenny from Olton TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I took 2 screws loose and undone water lines, replaced and reconnected everything. Real easy

Ice maker no working

  • Customer: Richard from Boise ID
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Removed water line. Removed two screws holding valve. Disconnected line from valve going to Ice maker. Replaced screws and water line. Most important thing in working with Parts Select was the information they provided when I called them. I had called electrolux and was given no information and was told they would send out a repairman at which point I told them to get lost. Cost of part $30.00 vs service call of $75.00.

Valve nut stripped

  • Customer: Jesse from Woodstock GA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Old part threads : made in China (brass) New part : made in Mexico (steel). First, unplugged it from the wall. As for the valve, removed the two screws holding the valve in, disconnected the plug, took the pipe cutter, cut the blue line to the ice maker, cleaned up the cut, pushed that line into the new one and reassembled. Done!
All Instructions for models starting with 25380
1-15 of 22