25380 Kenmore - Instructions

LOOSENED THE TWO SMALL SCREWS THAT HOLD THE ICE MAKER UP INSIDE THE FREEZER. DISCONNECTED THE WIRING HARNESS. TOOK THE OLD ICE MAKER OUT AND JUST INSTALLED THE NEW ONE IN REVERSE ORDER. LATER THAT DAY I HAD FRESH ICE FOR THE FIRST TIME IN WEEKS!

Pulled unit away from wall and shut off water and unplugged unit. Installed water valve and reassembled, plugged back in and turned on water and checked for leaks. All good. However there is no water getting into the ice maker. The unit itself is going thru a cycle of attempting to make ice and the bail is moving and you can hear the solenoid activate but no water. I have tried to blow thru the tube going to the maker but it seems to be plugged by something. I do not know if there is another valve up there or how to clean it out. Any help would be greatly appreciated.

was very easy. just ordered a new ice maker which was delivered in a few days. The installation was so simple. Just plugged the new ice maker in and hung the unit on the 2 screws. And then tightened the screws with a 1/4 in nut driver.

The repair was a simple swap of icemakers with a 1/4" nutdriver. I didnt get the first unit sent after 7 days, so I called PartSelect. They were very courteous and understanding. My icemaker arrived within 12 hours of my phone call! Excellent!

The screws holding the ice maker in place were backed out about a turn and a half or so. The icemaker was raised about 1/2 inch to clear the bolt heads. The icemaker was extended just enough to access the wiring harness connector. The connector was released, and the ice maker was removed. The replacement unit extension was unneeded. The wiring harness connector was attached, and the wire was wire-tied out of the way. The icemaker unit was placed over the screw heads, rested in place and the screws were tightened (only snug). Easy-peasy!

This would have been an easy repair, but I bought the Frig from Lowes and I think they added the icemaker. The replacement icemaker uint has a plug on it for easy replacement. My frig was hard wired so I had to cut off the plug and splice the wires. Not a real big deal but a small work space.

put in a new one

I needed one with the adapter. I installed it and there was ice in the tray the next morning...no problem

According to the online video instructions.

1-Unpluged the refrigerator 2- removed ice cube tray and some food( Placed in cooler )3- unscrewed the two screws holding the old unit lowering it and unplugged it. 4- Had to loosen the cooling coil to get to the pass through hole in the back and pulled the old wire out. Connected the wire adaptor to the old connectorand to the new ice maker. At this point I couldn`t pass the new plug through the back so I strapped it out of the way and installed the new ice maker using the two screws from the old one. Adjusted the fill adjustment and turned it on. Cubes in about 4 hours.

I watched the video and did the same thing on mine and now it is working fine

Took less than 10 min to install following the inclosed instructions. At first it was not making enough ice to make me happy so I set the temp. a little colder in freezer. Now making ice like crazy. Works better than the old one ever did. Very happy with the new replacement.

I followed the video that came with my email receipt but i had to use the extra electrical adapter, there is no where to put the extra wiring so it is hanging next to the wall. I was glad I didn't have to unplug the fridge. just kept the wire up so no water would come out. It took several hours to start working and it doesn't make as much ice as the old one, but at least it works. It was a very informative video. Thanks

I took 2 screws loose and undone water lines, replaced and reconnected everything. Real easy

We reviewed the video posted on your site for guidance. It was very helpful to see someone do the repair. The project went just as described in the video. Within 24 hours I had a full bin of ice!