Models > 2537419440R > Instructions

2537419440R Kenmore Refrigerator - Instructions

All installation instructions for 2537419440R parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 2537419440R
256-270 of 359
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Crisper drawer front was cracked. Retainer bar broke (1) and cracked(1)

  • Customer: Lorraine from Adelanto CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
One retainer bar was gone. I slid the other one that had cracked out and just slid the new ones in. Took no time at all. The crisper drawer, I just took out the old cracked drawer and slid the new one in. It is clear, where the old was manilla, but now I can see the fruits!! The only thing I wish is that the manufacturer had put a post in the center of the retainer bars so they would not crack. Also they stick out, so they allow smaller items to slip out. Again, manufacturer problem. Over all I am very happy to have found this company!! I did have to go to the website a few times as the last # on my appliance could not be read and I was not sure I was ordering the right parts, but I could have called. :)

door shelf bracket broken in half.

  • Customer: Raymond from Pawtucket RI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took less than 1 minute to install. Snap in and DONE. The easiest job ever. Thank You!

icemaker not working

  • Customer: Philip from Sheridan AR
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
first replaced dual solenoid, then ice maker. still not working. going to chase electrical next

Replace the handle mount

  • Customer: RUTH from AUSTIN TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
When I was moving the refrig. handles from one side to the other...I broke one of the mounts. It was SO easy to order from this place, and they ship IMMEDIATELY. Second time I have used them, and am VERY impressed.

Valve nut stripped

  • Customer: Jesse from Woodstock GA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Old part threads : made in China (brass) New part : made in Mexico (steel). First, unplugged it from the wall. As for the valve, removed the two screws holding the valve in, disconnected the plug, took the pipe cutter, cut the blue line to the ice maker, cleaned up the cut, pushed that line into the new one and reassembled. Done!

No ice - Replace water valve

  • Customer: G V from Bowie MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
TURN OFF WATER!! UNPLUG REFRIGERATOR!! Remove water fittings and electrical connector on old valve. Remove two mounting screws on pump bracket. Reverse procedure to install.

Water was leaking in the back whenever the heating element turned on, freezing up the ice maker

  • Customer: Jose from Las Cruces NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Loosened the two screws on the side wall, disconnected the old unit. Reverse the order for installation. There is a small bracket at the botton that helps level the unit. Be sure to remove that bracket and put it on the new one.

Brooken Drawer Rail Support

  • Customer: Mary Lou from Scranton PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The repair was very easy. I took out the top glass shelf which the drawer is attached to and unscrewed the broken support. Then just lined up the new support and screwed it in place. Placed the top shelf back in the fridge and slid the drawer into place along the new rail supports. Very smooth process.

Broken meat traysupport rail

  • Customer: Rusty from Newbury MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove 1 screw, pull out old part, insert new part, replace screw. Takes longer to clean off the fridge shelf than to replace the part.

Rattling Noise from behind frig

  • Customer: Michael from Rockford MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Initially, I traced the noise down to the evaporator motor area. I thought it was the fan blade so I ordered and changed it. Noise level better but still not good. Then I ivestigated problem area again. Removed the motor,discoverd that the motor shaft was loose /drifting which caused the "hummm" and uneven fan blade rotation. Orderd and installed new motor and all is good.

It would freeze up or not cool at all, depended where the clock stopped.

  • Customer: Roger from Owatonna MN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the lower trim panel from front of fridg. and loosened two screws enough to turn it about 1/4 inch so the screw heads were in the larger holes. Pulled it out disconnected the wire connector and transfered the heat shield and screws to the new clock, connected the wire connector and aligned the screws. tightened them and job done. Has worked like new sense. Thanks Roger

fridge not cold stays running

  • Customer: Joseph from Deland FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
unplug fridge,Then take rack out n remove the 2 screws on the icemaker set aside,then remove 2 screws on the back panel, cut wires n splice in new part! put back the same.

Refrig would not defrost

  • Customer: Robert from Jacksonville FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Diagnosis: used wiring diagram attached to frig and determined cause could be wiring, heater element, thermostat or timer. After completely defrosting the frig (turned it off) I removed the rear cover in the freezer and looked for an obvious problem. None seen. Removed temperature select pod from the frig box and looked for obvious problems. None seen but defrost timer appeared poorly made. Repair: Since I had no practical way of checking the defrost cycle in operation, I checked probable failures on the Part Select website and saw defrost timer as most probable. I ordered the timer. Installed it. Waited a few days to make sure the frig went through a few defrost cycles then removed the freezer rear cover. There was no excessive frost buildup so I'm reasonably sure the repair was successful.

Blacks specs in ice cubes, lining deteriorating,

  • Customer: Robert from Hatteras NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The repair went exactly as illustrated by the video offered by part select. That video was helpful and showed me step by step how to accomplish the repair. The replacement part was exactly the same as the original, thank you part select.( Allow the old ice maker to return to room temperature before you remove the 1/4 nut securing the level mechanism, otherwise the frozen head of the not will break off).

Drawer Supports Broke

  • Customer: Joan from Brooklyn NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
In 10 years, this is the second time these drawer supports broke and what a difference to fix. The parts came quickly, fit well and are very easy to install. The fridge is good as new and the cheese/condiment drawer is back where it belongs. Good quality and easy to do.
All Instructions for the 2537419440R
256-270 of 359