Models > 25371832102 > Instructions

25371832102 Kenmore Refrigerator - Instructions

All installation instructions for 25371832102 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 25371832102
61-75 of 497
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Refrigerator quit running

  • Customer: Frederic from Daytona Beach FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 12 people found this instruction helpful
I located the part that was the culprit as it had buzzed very much before quitting. This is an easy removal as the part is in a two prong jack and just needs to be carefully removed with the new part inserted back in the jack provided. The refrigerator works fine now, but the run capacitor will still buzz on start up of the compressor. I do hope this is normal in this model? anyway it runs fine mow. Thank you.

Shelf door retainer was broken

  • Customer: Lisa from Raleigh NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 6 people found this instruction helpful
Our refrigerator door shelf retainer had broken on the side which basically put one shelf out of commission in our fridge. I looked up our fridge on partselect and found the correct retainer and ordered it. The part came very quickly, within just a few days. If fit perfectly and I'm very happy with the part, the speed of delivery, and ease of ordering. I will definitely use partselect again.

ICE WOULD NOT WORK - BUT WATER DISP DID

  • Customer: JAMES from HENDERSON NV
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 7 of 9 people found this instruction helpful
SHUT OFF WATER/POWER - PULLED TRAY -LOOSENED TWO SCREWS HOLDING ICE MAKER - LIFTED IT UP AND OFF - UNHOOKED POWER CONNECTION
INSTALLED NEW MAKER IN REVERSE OF ABOVE - POWER SUPPLY LINE WAS MUCH TO LONG BUT JUST PUSHED IT UNDER THE ICE TRAY ( AWAY FROM THE MAKER )
PRIOR TO ORDERING LOOKED AT COMMENTS FROM OTHERS REGARDING INSTALLATION

Plastic shelf broke

  • Customer: Jim from Carlsbad CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 6 people found this instruction helpful
snapped in place in less than 30 seconds

Original Ice Maker quit working.

  • Customer: Gary from Azle TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 5 of 5 people found this instruction helpful
Loosened the 2 screws a little so that it would slide up and off then unplugged the wire harness.
Installed the new one in reverse order and works like a champ.

Even though the pieces read one thing they did not fit

  • Customer: sadre from long beach CA
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 6 of 8 people found this instruction helpful
I ordered 2 bars, 1 for the freezer and 1 for the fridge area, both bars were too big. I am currently looking for someone with a bandsaw to cut these parts to fit the fridge. The 'left and right' caps are perfect though.

No air flow in freezer or fridge

  • Customer: Jim from Au Sable Forks NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 7 of 12 people found this instruction helpful
Snap out fan cover, remove four 1/4" screws, remove back cover, remove defective fan motor, remove fan blade, install new motor and blade, strip wires and hook up with wire nuts, reinstall back cover, snap in fan cover, and plug in fridge.

Ice maker was not making ice

  • Customer: Jeffrey from Indianapolis IN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 5 of 6 people found this instruction helpful
I replaced the solenoid first because the ice maker was not getting water. After replacing the solenoid valve, I waited about 1/2 an hour, still no water. So, I ordered a replacement ice maker. I then installed the replacement ice maker, waited a 1/2 an hour, still no water. Then, I waited overnight. Yeah, ice! WORD OF ADVICE. WAIT OVERNIGHT TO SEE IF THE ICE MAKER CREATES ICE. Not sure how long a cycle takes, but it's longer than you would think. Hope your installation is a success!

my old ice maker leaked at the bottom

  • Customer: harry from terre haute IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 5 of 6 people found this instruction helpful
it was really easy changing the ice maker. the only trouble i had was the wiring. it was very stiff and hard to route. it did not work at first but that was my fault did not have the connector plugged in all the way.since then it works great.

Cracked drawer

  • Customer: Jaime from Harrisburg PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
I slid out the old drawer and slid in the new drawer. Easy as that! I would recommend this website to anyone.

Lightning struct the house and fried the evap thermostat

  • Customer: charles from parker CO
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 5 of 7 people found this instruction helpful
Noticed the evap fan wasn't working, so trying to disconnect the wire broke the connection so had to order a new motor. Installed the motor but it still didn't work. Had a technician look at it and he said it was the control board. Ordered and installed control board and still didn't work. The only element left is the evap thermostat. Jumped the thermostat and it worked so ordered and installed a thermostat. It works now

Had no freezer shelf.

  • Customer: Bettie from Toledo OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 5 of 7 people found this instruction helpful
I had to cut a little of of the ends of the shelf to make it fit. I used an angle grinder to get the job done and the shelf fits perfectly. By the way I paid for 3-5 day shipping and got it the very next day can't ask for better service than that.

ice maker quit making ice

  • Customer: Barry from Middletown DE
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 7 people found this instruction helpful
I basically followed the instructions offered when i searched for the ice maker. It was relatively easy to do, I undid the 2 screws holding the ice maker to the side of the freezer, the was the tricky part, holding a mirror so i could see the slots of the screws. loosened them, disconnected the electrical connection and reversed the process for the install. It took about 25 minutes and i was back making ice.

cracked bottom hinge

  • Customer: LEE from LEO IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 4 of 5 people found this instruction helpful
My 4 year old grandson used the frig door as a swing.The bottom hinge cracked, then the door wouldn't seal. I propped the door up with some books, removed the broken hinge (2 bolts) and replaced with the new part. Simple fix on the door, only time will fix the 4 year old!

Tha part was broken

  • Customer: yadira from mcallen TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 8 people found this instruction helpful
Very easy
All Instructions for the 25371832102
61-75 of 497