Models > 25371832102 > Instructions

25371832102 Kenmore Refrigerator - Instructions

All installation instructions for 25371832102 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 25371832102
451-465 of 506
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

no ice

  • Customer: Larry from Plains KS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
instructions were very simple. Took about 10 minutes to replace the unit. Do NOT get excited about immediate ice because it took mine awhile to g et cranked up for full production. Anyone can do this! Saves about $150.00 in labor to have someone(no smarter than you) do it for you.

freezer was icing upp and not defrosting

  • Customer: Ron from Gladstone MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
just followed the instructions from part select website - everyone is a repair man with the easy to follow and attention to detail the videos provided - time will tell I replaced the defrost timer and thermostat at the same time - the refrigerated was running a lot and the freezer was icing up on the back right of the freezer compartment mostly - " it has been doing this since the day we bought it from sears - we had a repair man over more than once but still had the same problem and had to max out the controls to keep things close to were they were suppose to be temperature wise. we also purchased a few extended warranties The freezer was running around 15 degrees and running all the time. The heating element checked out at 35 ohms so it must be ok. Will let you know in a few days. One serviceman even tried to say it was frosting up because we didn't have ac lol

Not making Ice/ unit not calling for water

  • Customer: Bob from Celina OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug refrigerator power cord. Remove ice cube bin. Place wire signal arm in down (off) position. Ice Maker is held in place by two (slotted/hex headed) screws through keyhole slots over the top of Ice maker along the left side of freezer. Use mirror to locate screws then carefully loosen (do not remove) screws with a nut driver or screw driver. Lift Ice maker up and right until it releases from the screw heads. Unplug electrical connection. A flat screw driver may be required to loosen connector. Connect new unit electrical and Install new unit over screw heads and tighten screws. Replace Ice Bin and place wire signal arm in the up (on) position. Reconnect refrigerator power cord. After freezer cools down sufficiently it will start making ice.

Original plastic hinge cracked across the middle

  • Customer: Al from Sarver PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed 2 hex screws & old hinge, placed new hinge on cabinet & found that it didn't fit; one hole was about 1/8" off. Had to drill a new hole in cabinet top in order to attach new hinge. Hinge works fine now. I'm glad to find the hinge is metal; original one was plastic.

The drawer was broken

  • Customer: Carol from Odessa TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just slid the new one into place.

warm fridge, cold frosty freezer

  • Customer: Jim from AuSable Forks NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
remove food, then the shelf, then use a hot air gun to defrost and loosen the back panel, then remove the panel, then defrost the coil and thermostat area. using wire tools, replaced the defrost thermostat,and re-assembled freezwr and test

Torn Gasket

  • Customer: Richard from Fruitland Park FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pulled the old one off, pressed new one into groove on door. First time it really was as easy as the instructions on line said.

Limited cooling in freezer and refrigerator, ice build up.

  • Customer: Wayne from East Alton IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed Internet video instructions for both parts. Two suggestions: Forget the heat shrink tubing and use electrical tape instead, tubing is short in length and difficult to use unless you have a correct heat gun. Secondly, my timer didn't click twice but due to instructions I could determine that the timing was correct in the operation after the first click. This method could be explained as well as when to start it in connection with usage to be the most efficient in temperature and operation.

The refrigerator part was not cooling enough

  • Customer: Mainul from Portland OR
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video online where it described the troubleshooting tips for this type of symptom. So I knew exactly what the problem was which is the defrost timer. After the part came in I just unscrewed (4 screws) the box which houses the thermostat and the defrost timer from top ceiling of the refrigerator section. Then I just unscrewed and unhooked the old defrost timer and replaced it with the new one. After finishing the installation I turned the fridge on. At first nothing happened. So I turned the dial on the defrost timer with a flathead screw until it clicked and the fridge came alive. I waited for an hour or so. The cooling cycle completed and the fridge stopped as expected. When I opened the door I noticed the interior is much colder than before and right after closing the door the fridge hummed back into life again. So I know my fridge is working again. Thanks to PartSelect for providing the right part for my refrigerator. I will definitely buy from them again if anything goes wrong.

The door bin had broken and needed to be replaced.

  • Customer: Anna from Stockbridge GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The replacement part simply snaps into place - super easy!

Frige and freezer not cooling

  • Customer: FRANK from BRADENTON FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I should have ordered start kit instead of start capacitor. The start cap astir did not fix problem so I ordered kit. Compasator comes as part of kit. Followed enclosed instructions. Cut existing wires and reconnected new wiring. Simple as that. It's a plug in item. Now worried it may be working to good. Freezer down to 10 deg. Watching to see if compressor is running to long. Seems ok lol. Wife hates me now. She wanted new frige.

Broken Door Shelf Retainer Bar End Cap - Right Side

  • Customer: John from Charleston SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed old broken end cap and installed it on the retainer bar, re-installed entire assembly

broken front of door shelf bin

  • Customer: frances from charleston WV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Opened carton....removed part....washed with hot soapy water....snapped in place.

Fridge door shelf was broken

  • Customer: erin from edmonds WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I love this site! Easy to order, easy to install!

broken crisper pans

  • Customer: Liliana from Kirtland OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
pulled out broken ones and replaced with new ones
All Instructions for the 25371832102
451-465 of 506