25371822104 Kenmore Refrigerator - Instructions

Reviewed the video on your website and followed the directions to the letter. Great video

Pulled refrig away from wall, shut off water supply. Removed two screws holding the old water value on the back of the refrig. Removed the two water lines from the value. Hooked water lines up to the new value and bolted the two screws and the new value on. Turned on water and pushed refrig back into position. Simple and it worked. No more huge blocks of ice. I have Cubes!!!

First, I replaced the defrost timer, really easy, 4 screws popped the cover of the electronic area (top of refrigerator compartment) took it out and plugged in the new time. Unit still would not defrost, so replaced the thermostat as well. Bit harder, removed ice maker, 2 screws, back plate from freezer, 4 screws. Thermostat was clamped to a copper tube- the original had one of the wires hanging out of it- cut the wires and crimped the new wires on, shrunk the plastic tube with blow dryer over the wires (taped them for good measure) and so far so good. Learned most of this through these tips, so keep reading if this isn't your problem, just save myself $1000 on a new refrifgerator...

This was really simple, much like changing a light bulb. Two bolts loosened beneath the old unit to allow it to be lifted off and free. The power supply plug was easily disconnected. The new unit was then placed onto the loosened bolts, power supply reconnected and secured with the supplied wire tie. A small angled bracket was removed from the old and reattached to the new as a support toward the from of the unit. The cycle adjuster was backed off a 1/2 turn as per the instructions....and the next morning....new automatic ice. Life is good!

The repair was very, very easy. The old Gasket was easily removed by pulling at (1) of the (4) corners and simply pull from slot around the full perimeter of the door. No tools of any kind are needed. Replacement of the new Gasket was simply to again start at (1) corner by pushing new gasket into the perimeter slot and using fingers push into the door grove all the way around. This install took no more than 10-15 minutes max.

Don't ever tell your 11 year old to clean the refridgerator. Something will almost definetly get broken like the glass shelf, but luckily I had parts select which in no time assisted me to find the exact part. I ordered the part, it came quickly and I replaced within seconds.
Thanks.

i removed the 4 screws holding cover. removed two screws holding timer. unplugged timer. plugged in new one. reassembled.

I had already removed the ice maker by loosening the two screws with a 1/4" nut driver, in order to compare the design and style to the intended replacement for size and critical measurements. The replacement was almost identical. The wiring harness was 2-3" longer than the original, but after snaping the wire plugs together I simply curved the wire up and to the left to be out of the way. The hanging brackets are slotted and it was easiest to slip the back hanger over the head of the screw and let it slip down, then the front hanger was already to line up even though you can't see the screw with the ice maker in the way. I had to transfer an L-shaped metal bracket to the bottom side, matching the old assembly, and adjusting it to hold the bottom side away from the freezer compartment a little so it would hang level and secure. You have to snug the two screws with a screw driver or 1/4" nut driver by feel, since you can't see them with the icemaker in place. It took about 10 minutes to take out the old and another 10 to put in the new. We now have a full bin of ice, and the old plastic trays have been retired. I should have done this a year ago.

Loosen two screws, unclip electrical connection, remove ice maker, remove l shaped leveling piece of metal from old one, put on new one. Install in reverse order. Hint.. when loosening two screws, use a mirror

First, unplug the refrigerator since you're working with live wires.

Remove the 4 Philips sheet metal screws holding the plastic housing that holds the temperature control to the top of the refrigerator compartment. Pull the housing down then out since there is a tube on the housing where the water flows out the back of the refrigerator during the defrost cycle.

Remove the 2 Philips screws holding the defrost timer on the plastic housing. Pull the connectors off the old timer and attach them in exactly the same positions on the new defrost timer.

Attach the new defrost timer to the plastic housing with the 2 screws.

Reinstall the plastic housing, making sure the water tube is inserted into the back of the refrigerator wall.

Plug the refrigerator back in and you're done.

I removed a couple of screws from the old part, and inserted the new part. Replaced the screws and I was done. No problem. I'm an almost 60 year old woman, and fixed this myself. It was so easy.

At first I tried to insall the new gasket with the door still attached to the refrigerator. It was difficult to assure that the bottom of the gasket was properly installed at the bottom. As a result I removed the door from the refrigerator, finished installing the gasket and then put the door back on the refrigerator

since I had my fridge since 2003 it seems that I've gotten my moneys worth but it has worked flawlessly with no issues. I did not want to part with it so I troubled shoot the system and realized that it could have been number of things so I just decided after reading some reviews here on this site I decided to just purchase the items that would be effecting the fridge not working properly which was the evaporator fan, defrost thermostat, defrost timer, temperature cold control thermostat, I also cleaned the condenser coils in the back of the unit so they can be able to withdraw heat from the unit. my repair and installation took about 4 hours due to the cleaning of the coils but now the fridge is working like brand new. thanks to this sitt and it's comprehensive video tutorials on installations and repair it my job a lot easier to do.this is not my first time ordering from this site and will not be my last. anyone considering ordering from this site do not hesitate there are great with parts and customer service.

Remove the broken piece by tilting upward and then sliding straight out.
Simply replace with the new door shelf by aligning the small hooks with the slots on the door. Tilt the shelf up, insert the hooks into the slots and then tilt the shelf back down to its normal postion. It is now locked in place and you are done!

Test the light socket first with a bulb that you know is good. If the light still does not come on, unplug the refrigerator, remove the switch by inserting a very small, thin, flathead screwdriver alongside it and pull the switch out slowly with your other hand. There are two wires there. Remove them gently with some needle nose pliers. If you want to test to see if the switch is defective, take a insulated jumper wire, and attach it between the two wires. Plug the refrigerator back in and see if the light comes on. If the light does come on, replace with a new switch by re-attaching the wires and placing it back in the hole firmly.