Models > 25371822102 > Instructions

25371822102 Kenmore Refrigerator - Instructions

All installation instructions for 25371822102 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 25371822102
76-90 of 497
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Tha part was broken

  • Customer: yadira from mcallen TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 8 people found this instruction helpful
Very easy

The meat pan hanger broke because it is made of plastic

  • Customer: Nancy from Olympia WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 8 people found this instruction helpful
I removed the glass shelf from the refrigerator to see how the plastic part was attached. I found a phillips head screw holding the piece in place in the back. I easily removed the screw and removed the broken piece. I then attached the new piece with using the old screw. ( a new screw was not included with the part.) Now it works like a charm.

ice maker went bad

  • Customer: nathan from gillette WY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 4 of 5 people found this instruction helpful
take the ice bin out of freezer. there are 2- 1/4" screws. these screws only need to be loosened a few turns. the ice maker can be slightly lifted up and will come off the screws. unhook the wire harness. take the "L" bracket off the old ice maker and put on the new one. set the new ice maker in. hook up the wire harness. put the new ice maker over the screws, tuck the wires out of the way and pull down into place. tighten the screws.

Lost parts

  • Customer: Nasser from Paterson NJ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 4 of 5 people found this instruction helpful
screwed the center hinge and spacer on the refrigerator then installed the center pin on the hinge and bottom door placed the top door on the pin and then screwedthe top hinge to the refrigerator,like new

Broken door shelf bin

  • Customer: Allan from North Miami FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 3 people found this instruction helpful
Opened the box, snapped it in place. Took longer to just open the box! I carefully inspected the part and compared to the original. I could not tell them apart. The fit and finish is perfect. This is a very well made product. Easy to order, fast shipping, well packaged and very easy to install.

I replaced the icemaker

  • Customer: Michele from Smithfield UT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 3 of 3 people found this instruction helpful
I removed the two screws and unplugged it. I then attached the pigtail to the appliance, then to the fridge. I had to push the excess wire harness into the hole in the back. It took a few minutes to move the rest of the harness out of the way by curving it upward and securing it with a nylon tie.I ordered the ice maker from Part Select on Sunday night and it arrived at 8:32 Tuesday morning, THANK YOU! I ordered very simple weed cutter parts from Sears a week ago and they haven't even shipped yet!

unit quit cooling

  • Customer: Steve from Cedar Park TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wiring harness plug, replaced the old timer with the new one, re-connected the wiring harness and reinstalled the mount in position. Hardest thing about it was lying on the floor.

both shelfs broke after jar slipped

  • Customer: christine from carson CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 3 people found this instruction helpful
removed both the shelf retainer and shelf bin, replace with the new units ordered from partselet.com. the whole process from searching, ordering, shipping and installing was very easy... thanks for everything

Ice maker quit working

  • Customer: Gary from Granbury TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 4 of 6 people found this instruction helpful
Remove ice pan below ice maker. Got mirrow verifed the type of screws. Obtained nut driver and felt it at right angle remove screws only have way. The ice maker lifts up and off. Took needle nose pliers to grip and remove electrical connection plug. The instruction and picture sent was no help the picture were the size of a thumb nail no detail could be determine. I installed the adapter plug and all the extra length wiring was the most difficult to type wrap with both hands extended out in front. I finally wrestled it in on to the two screws unscrewed from the wall about 1/2". Keep the ice maker water lever up and ensure it aligns to the water trough inlet. Works Great.
glg

freezer frosting over,fridge warm

  • Customer: Brian from Otterville MO
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 5 of 9 people found this instruction helpful
removed ice maker,,and screws holding back of freezer cover,unplugged wires and removed the cover and fan.wow,only wire to element had come unplugged!went ahead and replaced thermostat,and defrost timer,both were easy to do

refer door hinges were lost during the move in to our first home.

  • Customer: edith from woodbridge VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 7 of 15 people found this instruction helpful
The center door hinge was still attached to the refridgerator so I only had to install the bottom and top hinges. I also moved the door handles to the other side so the doors open the "right" way. The hinges were just 2 bolts and 3 screws. Now, just if the repair man from our home warrentee company would show up to fix the refridgerator. It's blowing hot air!!!

Old Defrost Timer Noisy During Operation

  • Customer: Vernon from Granada Hills CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 3 of 3 people found this instruction helpful
First I removed the plastic grill (pulled out, no screws) from bottom of refrigerator, then I removed electrical plug & two screws from old timer (timer located on the front inside left lower side of refrigerator). Installed in reverse order.

The meat drawer hanger broke.

  • Customer: Michael from Acton MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
I had to remove the top shelf of the fridge. Then the hanger just unscrews from a bracket of the back of the shelf.
CAUTION #1! First time around, I ordered the wrong side... there is a left and a right bracket. Unfortunately the on-line documentation did not show a label, or a difference between two part numbers.
CAUTION #2! The 1st replacement part I received (the one on the wrong side) was slightly different than the part it would replace... it would need to be modified to work correctly. A slot in the front of the original part was longer and deeper than that of the part I received... not sure if it would work even if the slot was deepened. Fortunately this was the side that was not broken, so hopefully I won't need to find out!

i smell very bad smell coming from refrigerator

  • Customer: Arsen from Glendale CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 15 people found this instruction helpful
I started look inside ,disconnected power, and open all possible compartments to see any burned part. Fortunately I fined a small part look like melted and then i went online and make my research .Then i ordered that part and change it.

Freezer too cold

  • Customer: Curt from Maple Grove MN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 3 of 3 people found this instruction helpful
Removed the housing with the light, 4 hexhead screws. This exposed the defrost timer, removed 2 hexhead screws, electrical connector and reassembled the unit.

Great resource and service, thank you.
All Instructions for the 25371822102
76-90 of 497