Models > 25365802508 > Instructions

25365802508 Kenmore Freezer - Instructions

All installation instructions for 25365802508 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the freezer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 25365802508
166-179 of 179
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Overheat coils at the bottom inside of the freezer

  • Customer: Costas from new hyde park NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I pick up very fast at these kind of small jobs but because of my very busy schedule I decided to call (2 times) technicians about my problem but none of them had any idea. About my repair, I removed the grill at the bottom of the refrigerator, unscrew a small plate (located on the bottom left side) that's holding the defrost timer. I plug on the new part, screw back the plate with the defrost timer and that was it. Don't forget to turn clockwise with your finger the timer until you hear a "click" and then turn it slightly more to the right. There is also a video on U-tube.

The only problem was that the part I ordered could only be used on the top and second shelf

  • Customer: MAXINE from GLENDIVE MT
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The shelf was out too far to be used on the bottom shelf. The top shelf, which was not as deep was then moved to the bottom and it worked fine. I am wondering if the shelf that was not as deep as the part I received is available. Thank you - Maxine

Freezer door sagging due to warped hinge

  • Customer: Keith from Springfield OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Just block the door up so it doesn't fall off, remove the two screws, replace hinge, and replace screws. My wife could have done it. Metal replacement part is much better than the original plastic that warped from day one.

no defrost +warm frig

  • Customer: Don from Holyoke MA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
watched vido on your site

changed defrost timer

  • Customer: Gerry from Apache Jct AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
followed the video very esay

Our refrigerator was not cooling below 50 degrees but the freezer had no problems. Turns out that the evaporator fan motor was dead.

  • Customer: Charles from Annandale VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I followed the instructions in the video associated with the part that I ordered. The video was perfect and described everything I needed to do clearly. Repair is 100% successful!

defrost heater not heating due to bad contact

  • Customer: Mark from Columbia MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I removed the back panel of the freezer using a nutdriver and located the defrost heater under the evaporator. It is strapped to the evaporator with aluminum straps that could not be undone without removing the evaporator (which would involve recharging the system and I have no tools to do that). I cut the straps with a nipper near where they were folded over each other (toward the bottom), and removed them. Fortunately there is a lot of extra strap, so I was able to remove the eye of the strap and reuse them. I removed the old element and installed the new, and wrapped the removed straps around the heater and evaporator where they were before, and plugged the element in. I did this on an old Kenmore refrigerator before also, and it had spring clips for the heater so you didn't have to cut anything. However, reusing the straps as I did resulted in the heater being adequately supported.

Freezer cold and frig warm

  • Customer: William from Miami FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Replaced evap motor. Everything is strong and running like a champ. Partselect video examples were very helpful. Would order parts again on next problem. Thanks

fridge side was getting warm.

  • Customer: Darryl from Russellville KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
open freezer door two screws just below unscrew slide piece to side unplug reinstall very simple.

Both gaskets were not sealing.

  • Customer: R. Evans from Las Vegas NV
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Called handyman and provided him with the parts. He took less than an hour,.

Broken shelf glass

  • Customer: Laurie from Chicago IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Insert the replacement glass shelf in my refrigerator. Installation was very easy and simple, no tools needed.

Freezer wouldn't go in to defrost cycle

  • Customer: John from Long Beach CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
After some troubleshooting to ensure the thermostat and heating element were working, determined that the defrost timer was the problem. With the defective part, I was able to manually advance the timer to activate the defrost cycle, but it wouldn't do so on its own. Unplugged the refrigerator from the wall. Timer is located in the refrigerator compartment at the very top. The compartment houses the cooling thermostat, the light bulb and the defrost timer. Using 1/4" nut driver, remove 4 screws holding compartment cover to top of fridge. Lower a bit to access electrical wiring. Wiring harness can be unplugged to work on the timer away from the fridge which makes it a bit easier. Timer is mounted with 2 phillips head screws. Remove screws and unplug timer from wiring. Install new timer, plug in wiring, secure with the phillips head screws and remount entire compartment.

broken crisper glass

  • Customer: Charles from Rogers AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
easy

Broken door shelf retaining rail

  • Customer: Brian from Sterling VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
It took less time to change out the rail than it did to take all the items off the shelf. Literally. Old rail holds on to the door with two snap in notches. I was able to easily unsnap the two ends of the broken rail and snap in the new rail in less than 30 seconds. No tools or mechanical knowledge needed.
All Instructions for the 25365802508
166-179 of 179