Models > 2536480240E > Instructions

2536480240E Kenmore Freezer - Instructions

All installation instructions for 2536480240E parts

These instructions have been submitted by other PartSelect customers and can help guide you through the freezer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 2536480240E
76-90 of 257
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

broken drawer support rail

  • Customer: Kathleen from Andover MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 3 people found this instruction helpful
replaced with new drawer support rail and put drawer pack in refrigerator

Defrost timer was not working

  • Customer: Harold from Grants NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Found the part on this site ordered and received part in 3 days. Took approx. 10 min to replace. Thanks for the quick service.

Refer iced up and would not keep the bottom cool. It was 70 Farenheit inside.

  • Customer: Larry from Newton KS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 1 of 4 people found this instruction helpful
I simply removed 4 screws holding the casing and then 2 more holding the timer. It was very easy. I then replaced the timer by unplugging and plugged the new one in. I replaced all the screws and the job was done. Less than 30 minutes. I was very impressed with the shipping time. When I ordered the part, I had it the next day.

Lost the temperature control know

  • Customer: John from Pilesgrove NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
The knob came in the plastic package. It was the correct part. I opened the package and placed the knob on the prongs. Now it works fine.

Thanks
John S.

The meat drawer slide had broken and the drawer would fall down everytime you opened it.

  • Customer: kathleen from cypress CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Pulled the drawer out, lifted the shelf out of the refrigerator, unscrewed drawer slides from shelf and rescrewed the new drawer slides and returned the shelf, drawer, and the job was finished. Thank you so very much for your speedy delivery.

Drawer support rail broke

  • Customer: George from San Bernardino CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Unscrewed the screw that held the suport rail to the shilf and changed the rail. Then I screw in the new rail.

one of the support rails on my deli drawer broke

  • Customer: Jennifer from Tully NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
first i removed the screw from the back of the shelf then pulled the old rail off. I sliped the new rail onto the post then replace the rear screw.

coil Iceing up

  • Customer: Thomas from Stuart FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 1 people found this instruction helpful
took 4 screws out of the discharge vent on top of the refrigerator section and unpluged the wiring harness and put the section on the counter and unscrewed the timer and put the new one in and reinstalled the assembly and plugged the Jack and put the 4 screws back in, and rotated the timer and put it on defrost removed the back and check the heaters and drain .

frezzer iceing over and not cooling the refrigerator

  • Customer: Marcus from Pine Hill AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 4 people found this instruction helpful
Just removed the two screws and unpluged it.
Then I pluged the new one in and replaced the screws. It runs like a brand new reffrigerator.
Thanks for the fast delevery. Will do busness with you in the future.

Broke meat keeper rail

  • Customer: Jo Ann from Ruidoso NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Removed shelf, inverted it, removed broken part (one screw), installed new shelf rail.

Piece of cake.

No freezing or cold in either freezer or refridgerator - compressor did not run.

  • Customer: George from Sunnyvale CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 1 people found this instruction helpful
Traced issue to defrost timer ( burned compressor & element contacts). This unit is mounted next to the temperature adjustment control in the refridgerator area - right in front. Removal of plastic cover provided easy access to the timer. Unit unscrews from the mounting then unplugs. Installation is reverse of removal.

The hanging drawer support on the left side broke and I was unable to glue it back together effectively.

  • Customer: Matthew from Murfreesboro TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I cleaned off the shelf that the drawer hangs from and removed it from the fridge. I took the philips head screw from the back of the broken support rail. Put the new one on, screwed it in and replaced the shelf and drawer.

Original support rail broke

  • Customer: amanda from burnsville NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Took longer to clear the top shelf to remove it from the refrigerator to do the repairs. Super easy!

Wife leaned on drawer and broke support.

  • Customer: David from Akron OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
The first thing I did was to remove all the food from the shelf above the drawer. I removed the old support rail that is attached at the rear of the shelf by one phillips screw. I installed the new support and secured it. Partselect was a great place to purchase the part and they shipped the part quickly.

Deli Drawer rail cracked

  • Customer: Chris from Goshen IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
As others have noted: this is an easy repair. I spent more time clearing all of our containers of yogurt that the actually "repair."

This is a good opportunity to clean the glass shelf and so I did that after removing it. Unscrewed the back support screw, removed old rail, and installed new one. (I just used the old screw as it seemed to be in good shape).
All Instructions for the 2536480240E
76-90 of 257