Models > 2536480240C > Instructions

2536480240C Kenmore Freezer - Instructions

All installation instructions for 2536480240C parts

These instructions have been submitted by other PartSelect customers and can help guide you through the freezer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 2536480240C
46-60 of 303
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

i smell very bad smell coming from refrigerator

  • Customer: Arsen from Glendale CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 14 people found this instruction helpful
I started look inside ,disconnected power, and open all possible compartments to see any burned part. Fortunately I fined a small part look like melted and then i went online and make my research .Then i ordered that part and change it.

Broken meat tray support rail

  • Customer: Henry from Newbury MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
Pull out the shelf and remove the one screw that holds the support rail in place. Remove broken rail, slip in the new one, then replace the screw. Done!

It takes longer to remove items from shelf and clean it than it does to replace the part.

Water leaking from fridge-drain tube cracked

  • Customer: Gerald from Goshen IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
Used a screwdriver and unstuck the tape holding the tube in place. Then, just wiggled the tube loose and snapped a new one in. Didn't bother trying to tape the new one. It stayed just fine. Space was a bit tight to work in, but not too bad. The most difficult part was figuring out that the water was actually coming from the fridge, not from a leaky faucet or drain. And the fridge was difficult to move, because it has no rollers in the front.

broken rack on freezer door

  • Customer: Louis from St Augustine FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 8 people found this instruction helpful
just slipped the part in place

the drawer support rail broke

  • Customer: Tara from Winsted CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
it was very simple, my husband did it. had to take the top shelf out and screw in the support rail and that was it. couldn't have been any easier. this was the easiest process from start to finish that we ever had. looked up on line, found your website, ordered the part and it arrived in a couple of days. So easy and your company was most efficient in having the part and in processing. Couldn't have been mored pleased.

rt slide for meat drawer broke

  • Customer: linda from garden city NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
easy. took glass tray that held meat draw out. unscrewed old rail screw new one in. put glass try back in frig. put meat try back in.

rack door broke in half

  • Customer: Lisa from Milwaukee WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 6 people found this instruction helpful
Rack door slid into place easily. Repair required no tools and took maybe 20 seconds to install!
Very easy job!

Broken drawer support and drawer'

  • Customer: Cameron from Bronx NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Drawer support held in by one screw drawer slide in no problem

Freezer came with no shelf

  • Customer: Henry from South Lyon MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
The shelf fit perfectly right out of the box. It was as if it was made for it. No tools needed except for the box cutter to open the shipping carton.

Bottom retainer bar on door shelf broke

  • Customer: Elizabeth from Shelbyville IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
took replacement part out of box and slipped it right into placed. could not have been easier

Rust on freezer shelf

  • Customer: Bob from Torrance CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 7 people found this instruction helpful
Perfect fit.

freezer frosting over,fridge warm

  • Customer: Brian from Otterville MO
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 7 people found this instruction helpful
removed ice maker,,and screws holding back of freezer cover,unplugged wires and removed the cover and fan.wow,only wire to element had come unplugged!went ahead and replaced thermostat,and defrost timer,both were easy to do

Left Support Rail broke

  • Customer: Frank from Chicago IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Most of my time was spent removing food items from the shelf that supported the rails. Once that was done, a quick removal of the screw, replace the left support rail and re-installing the screw. Done. I wish all of my repairs were so easy!

Old Defrost Timer Noisy During Operation

  • Customer: Vernon from Granada Hills CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 2 of 2 people found this instruction helpful
First I removed the plastic grill (pulled out, no screws) from bottom of refrigerator, then I removed electrical plug & two screws from old timer (timer located on the front inside left lower side of refrigerator). Installed in reverse order.

the plastic shelf in the door of the fridge broke in half

  • Customer: Jason from Orting WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
i opened the fridge door and slid it into place
All Instructions for the 2536480240C
46-60 of 303