Models > 25364802400 > Instructions

25364802400 Kenmore Refrigerator - Instructions

All installation instructions for 25364802400 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 25364802400
46-60 of 238
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

lunchmeat drawer support rail broke

  • Customer: Stacy from Chisholm MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 6 people found this instruction helpful
husband did it in less than 3 minutes. took top shelf out with part attached. one little screw to remove broke piece and one screw to install replacement part, good as new. took longer to clean the shelf before replacing it back in fridge.

drawer support rail was broken

  • Customer: Earl from Peoria IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Took one screw out to remove the old rail off by removing one screw placed the new one into the slot and replaced the screw and put the drawer back into the refrigerator

Left side rail support snapped off the lunchmeat drawer

  • Customer: Mary Lou from Scranton PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Used a small screwdriver to disconnect the left side rail from and replaced with the new left side rail. Everything went smooth and from start to finish, replaced the piece in about 3 minutes. Works great now!

Broken support rail

  • Customer: Robert from Duson LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
First, I removed the screw holding the support rail and, because of using super glue to attempt a temporary fix, I had a little difficulty in removing it from it's location.

Since I have "tremors" next time email me a repairman.

Thank you.

Robert L. Enox

Rust on freezer shelf

  • Customer: Bob from Torrance CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 7 people found this instruction helpful
Perfect fit.

Freezer came with no shelf

  • Customer: Henry from South Lyon MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
The shelf fit perfectly right out of the box. It was as if it was made for it. No tools needed except for the box cutter to open the shipping carton.

The original part was plastic/and broke

  • Customer: John from Lancaster CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 3 of 5 people found this instruction helpful
unscrewed to little bolts and installed the new/metal part we got rfom partselect.If we may say.this is a great company to buy from! Fast!

Crisper Pan

  • Customer: Deepankar from Novi MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 5 people found this instruction helpful
Just removed the broken pan and installed the new one within 2 minutes. Really simple

Freezer frosted up, refrigerator compartment heated up

  • Customer: James from Hanover ME
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 2 people found this instruction helpful
I removed the housing at the top of the refrigerator compartment that contained the reefer light and temperature adjustment knob. This required a small nut-driver. Inside, I found the old defrost control, unplugged it, unscrewed it with a Phillips screwdriver, and replaced it with the replacement part. Then I replaced the housing to its original position.

Job was really easy. Took less than 10 minutes

  • Customer: Neil from Sayreville NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
I easily removed the shelf, cleaned it, removed one screw, adjusted a tab that was bent, then installed new side rail with the screw that was removed and put back the shelf and storage bin. Everything worked perfectly. I must have saved $100 by doing it myself.

refer door hinges were lost during the move in to our first home.

  • Customer: edith from woodbridge VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 6 of 14 people found this instruction helpful
The center door hinge was still attached to the refridgerator so I only had to install the bottom and top hinges. I also moved the door handles to the other side so the doors open the "right" way. The hinges were just 2 bolts and 3 screws. Now, just if the repair man from our home warrentee company would show up to fix the refridgerator. It's blowing hot air!!!

freezer frosting over,fridge warm

  • Customer: Brian from Otterville MO
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 8 people found this instruction helpful
removed ice maker,,and screws holding back of freezer cover,unplugged wires and removed the cover and fan.wow,only wire to element had come unplugged!went ahead and replaced thermostat,and defrost timer,both were easy to do

Too much weight in lunch meat drawer

  • Customer: Tony from Toledo OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Emptied the shelf. Took out the shelf. Screwed in the one screw for the support rail. Put shelf back in. Put drawer back in. Works like a charm.

Left Support Rail broke

  • Customer: Frank from Chicago IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Most of my time was spent removing food items from the shelf that supported the rails. Once that was done, a quick removal of the screw, replace the left support rail and re-installing the screw. Done. I wish all of my repairs were so easy!

Old Defrost Timer Noisy During Operation

  • Customer: Vernon from Granada Hills CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 2 of 2 people found this instruction helpful
First I removed the plastic grill (pulled out, no screws) from bottom of refrigerator, then I removed electrical plug & two screws from old timer (timer located on the front inside left lower side of refrigerator). Installed in reverse order.
All Instructions for the 25364802400
46-60 of 238