Models > 25364802400 > Instructions

25364802400 Kenmore Freezer - Instructions

All installation instructions for 25364802400 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the freezer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 25364802400
196-210 of 220
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Refrigerator And Freezer Not Cooling Sufficiently

  • Customer: Peter F from Farmingville NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Refrigerator and freezer was not cooling sufficiently due to an inoperative evaporator cooling fan. Replacing the mini evaporator fan was extremely easy. Here are the steps needed to replace the fan. Step 1: Unplug refrigerator/freezer main power cord from the electric wall outlet. Step 2: Remove the food rack from the freezer compartment. Step 3: Using a 1/4" nut driver, remove the (2) 1/4" screws that hold the freezer vent panel/temperature control in place. Step 4: After removing the screws, disconnect the motor's wire harness connector which is located on the top left corner behind the freezer's vent panel/temperature control. Step 5: Pull away the entire vent panel/temperature control panel and lay it flat on a table. Step 6: Remove the vent cover from the main panel by holding the left side and the right side of the vent cover and squeeze both ends at the same time. Step 7: With the motor now being visible pull the motor's fan blade straight off. Step 8: Using the 1/4" nut driver, remove the (2) screws that hold the motor bracket to the rear of the main panel. Step 9: Using the 1/4" nut driver remove the (2) screws that hold the motor to the bracket and the (1) ground wire screw. Step 10: Install new motor back onto the bracket with the original (2) screws and the (1) ground wire screw onto the same locations.Step 11: Re install the (2) screws that mount the fan bracket to the back of the main vent panel.Step 12: Push the motor's original fan blade back on the shaft until it's fully seated. Step 12: Snap back in place the small vent panel back onto the main panel. Step 13: Push in place until you hear a click, the motor's wiring harness connector back onto the top left corner of the freezer's main power wire harness connector. Step 13: Push the main vent panel until it's in place and then reinstall with the original (2) 1/4" screws. Step 14: Reinstall the freezer's food rack back in place. Step 15: Plug in the main power cord into the wall outlet. Get ready to enjoy ice cold drinking water and a super cold freezer. Pete,your weekend mechanic

crisper drawer missing

  • Customer: Tova from Tarzana CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I ordered a new part and simply slid the drawer into place. The part fit as described and cost me less than another site selling Kenmore parts direct.

SHELF BRAKET BROKE

  • Customer: June from Littleton NH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
WE ORDERED A NEW BRACKET AND IT WAS INSTALLED AND IN IN LESS THAN 10 MINUTES.

crisper glass broke in thausand peaces

  • Customer: Alejandro from Auburn AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
it was easy my wife did it wen i went to the fridge it was already installed. thank you!!!!

FREEZER WORKED FINE, REFRIGERATOR WAS 47 DEGREES

  • Customer: Allan E from Manhattan IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I WENT ON PARTSELECT PUT IN MAKE AND MODEL NUMBER, A LIST SHOWED THE PROBABLE CAUSE. I WATCHED THE HOW TO VIDEO. WHEN I RECEIVED THE PART IN SHORT ORDER I LOOSENED 2 SCREWS DISCONNECTED THE WIRING PLUG (SPRAYED IT WITH CONTACT CLEANER) PLUGED IT IN, REMOVED SCREWS FROM OLD PART PUT THEM IN NEW ONE. PUT TIMER BACK IN ITS LOCATION AND TIGHTENED THE SCREWS. VERY EAZY, WORKS FINE.

Freezer working but fridge not cold.

  • Customer: Robert from South Park PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
My unit was not defrosting. Defrost heater was not functioning. Defrost heater tested good with a meter. Thermostat (cold) tested bad with a meter. Defrost timer was working properly. I replaced the thermostat but I had to buy red crimp connectors because the blue ones that came with the thermostat are designed for wire bigger than 18 AWG wire. The thermostat leads as well as the wire in my unit were 18 AWG. The crimp was not tight enough for my liking with the blue butt connectors. I also purchased smaller heat shrink tubing. After replacement, the defrost heater started working. I could see it glowing. Unfortunately immediately after getting the heater working the contacts in the defrost timer arced and stuck together thus preventing the timer from exiting defrost mode. The heater went off at this point indicating that the thermostat was now working. I then purchased and replaced the defrost timer and now the fridge is functioning properly. I noticed both replacement parts, even though I looked up my fridge model, were different part numbers than the originals. I'm guessing the new parts are improved? I also noticed the timer was an 8/30 rather than a 10/30 like the original. The fridge is working better than when it was new so evidently defrosting every 8 as opposed to every 10 hours is better for my unit.

Long story short:

Buy the correct crimp/butt connectors before beginning replacement of the thermostat and proactively replace the defrost timer since it is rather inexpensive.

Freezer coils icing up and fridge not getting cold

  • Customer: Aaron from Bedford OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I just watched the videos on the website and it was just as easy as the videos made it look.

The crisper glass shelf shatter when trying to clean it.

  • Customer: Leslie from Staten Island NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The repair, if you want to call it that, was a complete no-brainer. The glass slipped right into the shelf. No tools were needed. I was afraid that the glass might break during shipment. However, it was packaged and secured several times over that it was in no danger of breaking during delivery. The part came sooner than I anticipated. I am extremely pleased with this order.

Overheat coils at the bottom inside of the freezer

  • Customer: Costas from new hyde park NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I pick up very fast at these kind of small jobs but because of my very busy schedule I decided to call (2 times) technicians about my problem but none of them had any idea. About my repair, I removed the grill at the bottom of the refrigerator, unscrew a small plate (located on the bottom left side) that's holding the defrost timer. I plug on the new part, screw back the plate with the defrost timer and that was it. Don't forget to turn clockwise with your finger the timer until you hear a "click" and then turn it slightly more to the right. There is also a video on U-tube.

trim piece on shelf was broken

  • Customer: Sherrye from Trezevant TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just had to slide new part on to the back of glass shelf.

Freezer door sagging due to warped hinge

  • Customer: Keith from Springfield OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Just block the door up so it doesn't fall off, remove the two screws, replace hinge, and replace screws. My wife could have done it. Metal replacement part is much better than the original plastic that warped from day one.

no defrost +warm frig

  • Customer: Don from Holyoke MA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
watched vido on your site

Support rail broke

  • Customer: Donna from Olive Hill KY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I took the shelf out and took part off and replaced the new one.

broken rail

  • Customer: Donald from Kaw City OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove the shelf. Removed one screw. Removed old part and inst. new part with the one screw. Reistalled self.

changed defrost timer

  • Customer: Gerry from Apache Jct AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
followed the video very esay
All Instructions for the 25364802400
196-210 of 220