2480 Hoover Cooktop - Instructions

Simply pulled the old ones off and pressed on the new control knobs. It took less than 10 minutes, saved us from replazcing an otherwise nice looking range top, and made a big deposit in my "Honey do" account. I just wish they still sold the clock and timer units to fit this stove. Oh and yes, the prices were very reasonable too. Thank You Brad Harris, Illinois

The lids are fastened to the underside of the unit by rivets....3 to each lid.
I used a cordless drill and small drill bit to drill through the rivets to remove the old lids and remains of the rivets.
The new lids are easily fastened back using a rivet gun ( about $20 in Lowes) using small 1/8th aluminum rivets.
No real problems.
1 thing to note is that the drill bit will pass through the old rivet by about 1/4 inch before it comes up against the upper level of the BBQ floor so do not drill any deeper.The aluminum rivets are easy to drill through and you will easily feel when the rivet is drilled through.

Important: Down load the helpful assembly diagram for the fan motor and study it for a few minutes. It's very straight forward. Also a good idea is to remove the bottom panel which comes off easy before starting.

My only problem was removing the existing blower/fan wheel without damaging it once I had the assembly on the work bench. It was rusted on tight and managed to remove after a few tries using penetrating oil. The wheel is in stock and I'd suggest buying a new one along with the new motor if I had to do the job again.

Bottom line; the fan motor fit perfect but did have to re-use part of the old existing electric pig tail because the motor does not come with the factory type motor terminal connectors. By using three twist on wire connectors was back in business. The down draft vent works like new.

Wife is happy...

Wade

blower wheel was caked with dried grease clumps; replaced blower wheel, urethan foam and 3 motor isolators; blower/fan no longer vibrating cooktop.

removed two screws thenpulled element up unpluged wires

First I removed a screw that held the element in place then disconnected the two wires . Then I just reattached the two wires put the screw back in place and was done in about 10 minutes. Fairly easy fix, I had this go out a few years ago and had a repairman fix it, and saw how easy it was, so this time I did it myself. Easy job!!

Turned off power at breaker. Removed screws holding control knobs in position. Removed knob and unscrewed nut holding switch in place. Noted wire positions and undid connections. Connected wires to new unit. Replaced nut and screws and control knob. Restored power and checked operation. You can do this. Don't call an electrician.

I TURNED OFF THE POWER TO THE GRILL FIRST. Then Removed the knob on the top face plate and then removed the 2 self tapping screws at the high end and this allowed the face plate to be pushed forward. And allowed access to remove the switch I removed the wires one at a time and replaced them on the new switch. All done in 20 minutes.

Our stove is from 1978 and was missing all but one drip bowl. I bought all the replacement parts from all the store, (Walmart, Target, Fred Meyer) nothing fit. I finally found this site and they fit perfectly! Thank you. If I have to keep the stove a while longer at least it looks clean and new now, and it still works great!

The 15-year-old Jen-Air stove started smelling really bad. I thought it was a dead animal stuck in the exhaust tube which runs under the floor to the outside. I flushed it out with clorine bleach, but it was still bad. It turned out to the be the grease filter. I washed it every week in the diswasher, but it just was not enough to get it clean enough. Finally, the grease went rancid and smelled really bad. This "repair" took about 30 seconds.

1. Shut the breaker off; Jenn-Air's design will have you working around hot leads if you don't.
2. Raise the control panel
3. Remove burner and unscrew the burner connector; trace the wires back to the control panel bottom and remove them
4. On the replacement connector, add the electrical for the control panel. These are not included and can be found at any hardware store; they are a standard size.
5. Connect the new wires and put everything back together.
6. Reset the break and test.

:-) - Just removed the old one and replace with the new one. Nothing to it. Takes 30 seconds.

This was so easy. I've looked for years in stores for these pans. I finally tried the Internet, found PartSelects and, holding my breath at what i'd find, voila'...perfect fit, perfect replacements. And it took just a couple days to arrive. I'll definately be back!
/John

Simply pull off old knobs and replace with the new parts. Didn't think I was going to find replacement parts. The equipment is actually over 25 yrs old. Thanks for partselect.

Everyone was amazed we could still get parts for our 25 year old Jenn-air stove top. Easy installation, hands only, couldn't be happier with the easy of ordering, the fast shippment, the quick replacement. Thanks!