Models > 22RA-4 > Instructions

22RA-4 Maytag - Instructions

Installation Instructions for parts on models starting with 22RA-4

These instructions have been submitted by other PartSelect customers and can help guide you through the repair with useful information like difficulty of repair, length of repair, tools needed, and more.

Models starting with 22RA-4

All Instructions for models starting with 22RA-4
1-15 of 35
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The grommets came apart metal from rubber.

  • Customer: Frank from Pierce ID
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 11 of 14 people found this instruction helpful
I replaced the broken grommets with the new ones. I purchased 8 so I would have back ups because I did not feel the new one would last either. I think they cost TOO MUCH but I could not haggle for price.

range top loose, grommets missing

  • Customer: joseph from wildomar CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 11 people found this instruction helpful
very easy to push each grommet into range top holes

Replacing the bulb in the freezer side

  • Customer: Yafa (and David) from Bothell WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 4 of 5 people found this instruction helpful
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Factory installed hinges were bent, preventing the oven door to close tightly

  • Customer: Tom from Issaquah WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 6 of 11 people found this instruction helpful
Had to turn off the propane, disconnect the propane line and then remove several screws holding the stove in the cabinet. Once I was able to pull the unit out of the cabinet, I had to remove several other screws for the sides in order to gain access to the hinge arm and spring. The front of the oven door had to be removed in order to get to the hinges. Replaced both left and right hinges, hinge arms and springs. After replacing all of the screws, I reinstalled the stove into the cabinet and reinstalled the screws securing it to the cabintet. Reconnected the gas line and checked for leaks. None found. Oven door operates properly now.

Oven rack missing

  • Customer: Pauline from Weedsport NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 3 people found this instruction helpful
Opened oven door, slid in rack , closed door...
Fit perfect....

missing gromet

  • Customer: Hal from National City CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 7 people found this instruction helpful
Pushed into hole by hand, really simple

Igniter wouldnt turn- knob spinning on shaft

  • Customer: Tim from Prosser WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Pull knob off igniter shaft, remove two screws, take out igniter, unplug wire. Reverse to install. Would have been very simple except the metal insert that is supposed to be inside the new knob was missing from the kit. I tried using the old insert in the new knob but it did not fit tight enough and would spin on the shaft. Had to use the old worn knob on the new igniter. Customer service said they don't carry the inserts. What? The brand new knob is useless! Needed to get the stove fixed so I didn't bother returning the entire kit. Oh well, stove works now!

THERMOSET W/FLANGE , FOR THE OVEN

  • Customer: John from Angleton TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Socket set, Wrench(Adjustable)
  • 4 of 9 people found this instruction helpful
THE FUEL LINES HAD TO BE CROSS OVER FROM THE FACTORY POSITIONS WHICH MADE ONE 3/8" TO SHORT. RESOLVED PROBLEM BY CUTTING THE SHEET METAL ON THE BACK OF THE STOVE TOP FROM 1" HOLE TO 1.5" BY CUTTING A SLOT IN THE LOWER PROTION OF THE HOLE WHICH WHEN BENT DOWN ALLOWED ME TO REBEND THE FUEL LINE DOWN GIVING ME THE NEEDED LENGTH TO RECONNECT THE FUEL LINE. NEW THERMOSET/FUEL VALVE WORK GREAT UPON COMPLETION. SINCERELY JOHN O.BEVERS

igniter not working on magic chef stove on 60 foot yacht

  • Customer: Timothy from Vacaville CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
called and ordered the part. it arrived the next day. amazing. put it in and all was well./ another happy yacht owner.
Tim Wiest
Tim Wiest yacht Service

Old knob is broken

  • Customer: DONNA from WARREN PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
This item had to be returned. Didn"t fit. Our shaft is shorter, and the new knob would not stay on.

Needed a second oven rack for RV oven.

  • Customer: Michelle from Silver Springs FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 7 people found this instruction helpful
With a family of five a needed an extra oven rack as my RV oven is very small. After much aggravation between calling and going online to the manufacturer I still could not get any help. Even with locating the all important parts number. I was just about to give up when I was surfing around and found this website. Wow! What a relief! Not only did you show my where to find the part number, but I ordered it and got it within days. I spent more time on hold and online with the manufacturers customer service than anything else. From now on, no matter what I need, whether RV or home, I'm going staright to PartSelect. Thank You and my family thanks you too, as we wil be camping on Turkey Day and now I'll be able to get all the meal done at once! Happy Thanksgiving! God Bless

oven light burnt out

  • Customer: William from Schwenksville PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 7 people found this instruction helpful
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

light bulb went out in my oven

  • Customer: Janet from Ada MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 4 people found this instruction helpful
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

Ignitor shaft and knob sheered

  • Customer: Tim from Santa Paula CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
This is a small RV cooktop. There is no pilot light but each burner will light using the spark type ingitor twist knob. Raise the front of the stove cooktop. It is on a hinge. Replace the ignitor assembly using existing screws. There is a very small anchor pin on the ignitor assy. which protrudes 1/16" from the base. The anchor pin hole had not been drilled into the stove face plate which prevents the ignitor assembly from twisting when engaged. So I drilled a 3/16 anchor pin hole exactly where required. It is important to be exact so as to align the installation screw holes in the face plate. These holes can be enlarged if need be however. Align the pin with the anchor hole and install the 2 existing screws. Attach the ignitor lead to the ignitor assy. and install the new knob. Close the stove top and start cooking.

igniter would no longer work, it would stick

  • Customer: Randall from Rochester NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 5 people found this instruction helpful
pull knob off streight out. remove two phillips head screws, disconnect wire to disassemble. To reassemble reattatch wire to replacement igniter, screw in two phillips head screws and push on the knob.
All Instructions for models starting with 22RA-4
1-15 of 35