22FN-6KLX Magic Chef - Instructions

You had alerted that it was imperative to unplug unit before starting to remove defective bulb. As described, there was silicon on bulb and socket and bulb broke upon my attempt to remove. Had to use needle nose pliers to get metal base of old bulb from socket, then all went well.

After watching your do-it yerself video, I turned off the gas and unpluged ac power cord, I removed the stove door and then removed the bottom tray inside the stove unscrewed tray plate pulled buner out of its housing. I then unscrewed the two screws to the old ignitor and unpluged it. Pluged in the new one screwed it to the burner bracket, put everything back togher then tuned on the stove. IT WORKS!!

The seal is suspended by metal clips at each end, which are inserted into holes in the oven box. The clips on the new seal were a bit too wide to fit into the holes. so I drilled the holes larger, and it worked fine.

Used old screws, as no new ones included. New handle for upper oven aligned perfectly with screw holes. Excellent image on website made us believe this would work and it did! We are not mechanical types, but this was very easy. Thrilled to replace the old handle with new one that was exactly like it, though stove is more than 35 years old, and this upper oven model doesn't seem available any more. It is not a microwave!

Removed the oven burner changed the igniter reinstalled the burner still didn't operate,gave up purchased a new range. I liked dealing with your sales department very friendly.

My Magic Chef is more than 30 years old, after all those years, the stove handle broke off in pieces. I found you online and with your help was able to order a new part which arrived lickety split. It took about 5 minutes to remove pieces left of the old handle and install the new one. I love you, almost as much as I love my appliance!!!

This is one of the easiest home repairs I have ever done. I shut off the gas and unplugged the oven. I removed the door and shelves. I then removed the two screws that secured the igniter and pulled the connector through the hole in the back of the the oven. No need to splice any wires as the replacement igniter came with the correct connector. It was then just a matter of reversing the process. Very simple and quick fix.

Replaced the oven igniter and oven works perfectly 30 seconds to light

I watched the video of the repair that was on the page, and said, "Oh, it can't be that easy." It was. I just followed the steps he did, and the had the old igniter out and the new one in in no time. I did have to go back in and add the new insulation, as I thought the old would be sufficient for the new igniter, but, other than that, I had it in and out in just a few minutes. The video was really, really helpful! If you don't know what you are doing, just watch it!

The oven in my Jenn-Air range started to leak gas whenever I turned it on and a visit from the local gas company indicated the ignitor had probably gone bad. I had assumed the older range wasn't worth repairing but didn't want to spend $800+ for something in otherwise excellent condition. Internet research yielded lots of tutorials on how to make the swap and I decided to see if I could get the old part out before going any further. It wasn't too tricky except one of the two screws holding the ignitor in place had stripped and it was in a location that was very difficult to reach. I used a part of tin snips to cut around it. The new part ordered here came very quickly and exactly matched what I had removed; the wiring harness fit perfectly. It was a snap to put back in and now the oven works perfectly. All for under $50.

My oven would not come on so my wife could bake a cake. The glow coil that ignites the gas for the oven had burned out. The replacement went very easily and fast. This web site was very helpful with all the information I needed to get it up and running again. I enjoyed the cake she made after I got it fixed.

Removed oven door, bottom, bottom of broiler and back metal shield. Just unscrew old igniter and unplug wires and install in one. No problems.

remove oven door (watch video) remove bottom drawer clipped off plastic connector and wirenut to existing wiring. use nut driver to remove old igniter and install new one they even supply wirenuts and new insulation. Instrution are very detailed and easy to follow.

Watched the u-tube video of the repair linked to the PartSelect website and followed the instructor. The screw on the old igniter was a bit rusty and stuck on tight but it came off with a bit of coaxing. I can't the part arrived so quickly and that the repair was so simple. I am so happy we did not have to buy a new stove!

Watched the you tube video. A tremendous help. Now it works great. I will definitely buy parts from you again!