Models > 22403 > Instructions

22403 - Instructions

Installation Instructions for parts on models starting with 22403

These instructions have been submitted by other PartSelect customers and can help guide you through the repair with useful information like difficulty of repair, length of repair, tools needed, and more.

Models starting with 22403

All Instructions for models starting with 22403
46-56 of 56
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The burner didn't heat to full temperature.

  • Customer: Stephen from Grants Pass OR
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
First turn off the power to the stove/oven. Next I removed the 4 screws located on the bottom surface of the control panel. You need to open the oven door to see/access them. The control panel can then be removed by rotating the bottom outward which allows the flange on the top to disengage. Next remove the two screws that hold the switch to the control panel. Note which wire goes to which spade connector. A quick photo can help. Undo the wires. Remove the old switch. Reinstall the wires. Mount the new switch to the control panel. Mount the control panel back into the stove/oven. Turn on the power and test. The burner now works as new!

Burner stays hot

  • Customer: Gregory from snellville GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
First turn off breaker, then take screws out switch assembly,take oid switch out, put new switch on,turn power on.

Burner would stay on high, on all settings.

  • Customer: Robert from Attleboro MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
In response to your question.......everything went perfectly!! The reason?? I read the directions that were very easy to follow. It was a quick, easy repair, and the stove burner is working like new.

Thank you for your help!!

Bob

Burner always on high, no temp. adjustment.

  • Customer: Woody from New Castle VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed 4 screws, tilted cover up and lifted out, removed wires from switch, removed 2 screws holding switch, lifted switch out. Replaced with new switch, connected wires, secured cover with the 4 screws. It worked!

Left Rear Burner would not work

  • Customer: Sharyl K from Nampa ID
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Shut off breaker, removed the top by unscrewing the retaining screws and removing all knobs and grommets. Removed control from top panel by unscrewing, removed 5 wires and placed on new control. I then remounted the control, placed the top in its well, fastened. Replaced the retaining screws in the hold down strip and replaced grommets and knobs. Returned power to panel by turning the breaker on and tested. Used later that evening to grill 2 panini.

Dropped cast iron pot broke switch shaft off

  • Customer: Robert from Clive IA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The video you provided was excellent! Turned the circuit breaker off. Removed four screws, pulled out control panel, took a picture of the wiring to be safe. Disconnected the wires from the damaged control and removed it (two screws removed). Mounted the new control, connected the wiring, replaced the control panel and the four screws. Circuit breaker back on, turn burner on. That's it. Thanks for the video!

Needed to replace a burner switch for an inspection

  • Customer: Dan from Greenville OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the cover plate for the burner switches and verified the wiring on the other switches. I had removed the bad switch a few years ago and I needed to make sure that the wiring was correct. I did not keep the original screws that hold the switch in place, because I destroyed them when I first removed the old switch. The were corroded from years of cleaning solution. I made new screws from longer wall socket screws by shortening them with a hacksaw. The entire process took about 30 minutes to do, and the results were good. The new switch is smoother than the others, but functions exactly the same.

switch on top of stove

  • Customer: James from Beaufort SC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
James is an electrician so he istalled the part himself

Rear butner no longer worked after liquid was spilled on range.

  • Customer: Paul from Bothell WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Just followed the instructions on this site... :) Unscrewed the front, removed old unit taking care of which wires went where, put in new unit. Voila.

Burner was very hot regardless of setting

  • Customer: David from Woodland Park CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Your site helped me determine the problem. You included a video of how to do the repair. The replacement of the parts went just as expected. The parts came quickly and were the correct parts. I could not have asked for a better experience. (I replaced two switches because the knob was loose on the othe one).. Thanks.

Rear burner was not functioning

  • Customer: Michael from Port aransas TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
used a multimeter to determine that power was going to the surface burner infinite switch. then determined that power was not going from the output side of the switch to the burner element. Turned power to range off at the breaker box. Removed eight screws total on range top, four on the cartridge side, two located on back of control plate where the downdraft vent is located and two on the double fixed burner side. Raised the range top to gain access to the infinite switch assemblies. Removed to TORX head screws retaining the infinite switch and then disconnected the five wires on the bottom one at a time, making sure to replace in the exact location on the new switch. Installed TORX screws in the new switch and installed all screws back into range top. reinstalled cartridge and burners and turned power back on. Tested rear burner and all functioned properly.
All Instructions for models starting with 22403
46-56 of 56