22388L0 General Electric Range - Instructions

first open oven door a couple inches and slide door up off hinges, then removed storage drawer to gain access to hinge spring, remove hinge spring with pliers noting which hole spring was attached in.then remove three screws from hinge and installed new hinge put three screws in attached spring back and put storage drawer in and oven door back on.

Turn off power at the circuit breaker before working on electric thing.

Removed oven door and shelves for free access to element. Unscrewed the old element, pulled it out, removed the clips and removed the element. Reversed these steps to install the new element. Tested the element to ensure it worked.

Really easy.
1) Pulled up on oven door and removed it.
2) Removed lower drawer to access springs.
3) Pay attention to which hole the springs are attached under the oven.
4) Remove spring with Needle Nose Plier. If you remove by hand, the spring will likely cut your finger....like mine.
5) Unscrew 3 screws of old hinge assembly.
6) Reverse process when placing new assembly in place.

I tapped the screwdriver with a hammer lightly on each of three screws to loosen them. I checked to see the position of the spring on the hinge. I then removed the hinge, put on the new hinge and placed the spring in the exact same position. The door works very good. The hinge replacement was a no-brainer.

first i removed the two screws that hold the element in place. then pulled the element out about 3 inches and disconnected the two wires .then i connected the two wires and pushed thebake element back and replaced the two screws.then i put the circuit braker back on and tested the stove and it worked great. very easy to do.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires,held wires one at a time so tehy wouln't slip back into rear holes in oven, slid off connector tabs and pushed on to replacement unit...)

The job went over without a hitch, only probably didn't get the correct part first go around, but after getting the right part everything went very easy..Just a couple of screws where the elment goes in and 2 wires to plug back into the new element, after that everything was good to go!!

First unplugged it. Then removed everything in side for easy access. Took screws out 2 of them. Had to pull to removed elemnet . That took a while. Should have tried removing other screws or at less loosen them. It went in easy. And lift off we had red burner. hey..

First turned off the power to the stove at the breaker panel, thenI removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Disconnecting/reconnecting the "clips" was the only difficult part because they did not slip off/on easily. Replaced the element in the oven, replaced the screws...good to go!

Best part of buying from Parts Select was that they shipped the part the same day I ordered it, which was the Friday after Christmas. Competitor would not have shipped till the following Monday and we needed the oven ASAP!

Pulled out bottom drawer and showed my 13 yr
old boy that the spring needed to go back in same hole, then he did the rest. It was so easy, even a 13 yr old can do it.

I unscrewed the two screws inside the oven, then i pulled the oven away from the wall and unscrewed the protective shield, and undid the wiring. Then i removed the element. Once the new one arrived, i pretty much just did the same thing in reverse. vwa-lah... fixed!

Slid off the oven door and loosened the hinge assembly. Removed the storage drawer to unhook the spring and then took off the old hinge assembly.

Inserted the spring into the new hinge assembly and then installed it - just tightened the screws. Hooked the spring into the lower point. Slid in the oven door and tested it so that is opened/closed easily. Cleaned under the oven while the storage drawer was out.

We can now bake bread, pizza, etc. What a relief.

.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)

I turned off the power going to the stove, unscrewed the 2 screws, plugged in the 2 inserts, put the 2 screws back and PRESTO!!!!

Shut of circuit breaker. Removed two screws with socket set . pulled element out about three inches, disconnected and held wires in place with clip type closepins. pressed connections onto new element , secured screws and presto... All too simple and in less then 15 minutes.
Reading previous reviews was quite helpful