Models > 22116 > Instructions

22116 - Instructions

Installation Instructions for parts on models starting with 22116

These instructions have been submitted by other PartSelect customers and can help guide you through the repair with useful information like difficulty of repair, length of repair, tools needed, and more.

Models starting with 22116

All Instructions for models starting with 22116
1-15 of 58
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

replaced filter

  • Customer: ELOISE from MILFORD OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 459 of 462 people found this instruction helpful
pulled old one out , cleaned the area & replaced with the new one.

Old grease filter that I actually did not know I had to change

  • Customer: deborah from fort pierce FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 439 of 519 people found this instruction helpful
Removed the old grease screen and cleaned the entire area thoroughly and replaced the screen

My Jenn-Air is an "antique." The filter was disgusting!

  • Customer: marion from aspen CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 158 of 303 people found this instruction helpful
I had put up with a filter that got more and more raggedy every year, but I thought my 30 yr. old range/grill top was too old for me to find an replacement filter. What a great service you offer. I found you by web-surfing, typed in the model #, and presto--you sent me the shiny new filter. All I had to do was pop it in and throw away the nasty grill (after washing the scent off to keep the bears out of my Colorado garbage.) Thank you!

Falling apart 20 year old grease filter for downdraft counter rangetop

  • Customer: Roe from Raleigh NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 144 of 286 people found this instruction helpful
Cleaned out the downdraft cove, inserted the new filter, and put old filter in garbage can. Laughing. Thanks. Wish you had a FAQ's hotline. I'd like to know if the radiant inserts fit the older coil-type models.

Burner Switch Broke were Knob attached

  • Customer: Malcolm from White House TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 15 of 18 people found this instruction helpful
First I cut off power supply, removed screws that held panel on, pulled the switch up and disconnected wires. Installed new switch, being sure to connect wires in the correct places. Refastened panel to stove top. Turned power back on and tested switch and it Worked.

Just ugly this time`

  • Customer: Susan from Chino AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 11 people found this instruction helpful
It's wonderful to get accessories for this 20 year old Jenn-Air. I love it and now it looks like new.

fan switch shorted out

  • Customer: Shane from North Richland Hills TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 7 of 7 people found this instruction helpful
This repair was so easy. After I examined the faulty part, I removed the old switch fom the control box by using a pair of pliers to loosen the flange nut holding the old switch. I removed it, and put the new one in by reverse order. The old switch was actually the original switch- about 25yrs old. It took longer to open the box. I couldn't believe I could do it and how much I saved in doing it all myself!!!

Two heating elements couldn't be controlled - full on

  • Customer: Lansing from Alamo CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 6 of 6 people found this instruction helpful
Turned off power.

Removed two screws to free up section of cooktop containing 4 switches - 2 good, 2 damaged. Removed the dials from top of the 2 damaged switches. With an adjustable wrench, loosed nut on stem of switch that fastened switch to assembly. Noted which of the 5 wires on each switch went on which tab. Pulled off 5 wires on one switch, finished removing the nut and removed broken switch. Put in new switch, attached the nut, and replaced 5 wires in exactly the same position, Tightened nut. Replaced dial. Repeated procedure for second switch. Placed section containing the 4 switches back on cooktop and inserted/tighted 2 screws holding it in place.

Turned on power.

Told cleaning people to NEVER put aluminum foil under the burner units again. The foil shorted across the power and damaged the switches.

Control switch broke off at the knob

  • Customer: Deborah from Newburg MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
My husband actually did the repair and it went very smootly. He removed the palnuts on all switches even though we were only replacing one switch. Then removed the two screws to the switch cover, and slide the cover up to expose the switches. He then took off one wire at a time from the old switch and replaced it one the appropriate place on the new switch. Exteremely easy repair and thank goodness because I (his wife) was the one who broke the switch. Thanks PartSelect!!

Infinite switch ran more than one burner

  • Customer: Stephen from Andover MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 13 of 29 people found this instruction helpful
Purchased 1 infinite switch and installed it on the left front burner. problem still there so I used the switch that I replaced on the rear burner and all was ok. The front switch had been sending full heat to the rear burner,but the problem ended up with the rear switch. The switches are interconnected and all are the same part number.Diagrams on partsselect were the key to a successful repair.To access the switch you need only to remove the fan cover, remove the 2 screws holding the switch assembly and move it foreward and then lift to reveal slide on connectors. Power to the unit is off at the main panel during the entire process.

Indoor grill over burner melted with fire

  • Customer: Ron from Lees Summit MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 7 people found this instruction helpful
Just put the new grille into place (2 pieces). They fit perfect. I visited several sites and yours was the first one that provided a picture to make me sure I was getting the right part for a jenn-Air unit over 30 years old. thank you

one side of cooktop did not work

  • Customer: Rebecca from Broadway NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 5 people found this instruction helpful
I took out the side of the cooktop that did not work. I had to take off the bottom of the cooktop and checked where electricity was going and not going. Once I found the part that needed replacing, I went on the website, search for Jen-Air cooktops and model number. From the sketch on the website, I was able to order the part needed. I decided to get 2 in order to replace both parts at one time, just in case. The part arrived quickly and was easy to install. The most time I spent was taking the backside off the cooktop and cleaning it.

two burners had failed to work properly. Always went to full heat.

  • Customer: Lark from Mill Creek WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 4 of 5 people found this instruction helpful
I first removed power from the stove at the breaker panel. Next, I used the assembly diagrams provided by the parts select website to determine how to open up the stove panel. I opened the oven door to access the four screws holding the front panel holding the knobs. I removed the screws and was able to tilt up the front panel to allow access to the four burner switches. It was easy to swap out the wires on the old defective switch to the new replacement switches. I replaced both defective switches in 15 minutes and tiled the front panel back down into its normal position and put the four screws back into the panel to secure it. Then I turned on the breaker and did a check to see that the parts I replaced were working properly. They were and the total repair time was around 30 minutes without rushing at all.

All four of the cooktop switch controls needed replacing since none would control their respective burner.

  • Customer: William from Williamsbirg VA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 4 of 5 people found this instruction helpful
Turned off the power at the circuit breaker panel. Removed the control knobs from each switch and the four palnuts under each knob. Removed the two screws inside the vent well that hold the escutcheon in place. Pulled each switch up as much as possible to expose the wires attached underneath to each switch blade. Remoced each wire and replaced them on the new switch. Same procedure for all four switches. Reassembled in reverse order. Turned on power and all four burners lit up and were regulated as if new. I saved $244.00 doing the repair myself.

burner on electrics range was either off, or fully on

  • Customer: Dale from Alpharetta GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 3 people found this instruction helpful
The burned control switch was not functioning. It took a while to find the range model number and then the part number of the switch. It was cool that I could see a picture of the part with the part number on the internet so that I was sure to buy the right part.
Once the part arrived, I turned off the power to the range (circuit breaker, 220 V) removed two screws, used nut driver to disconnect switch handle, marked the 5 wires going to the switch, used the needle nose plier to remove the wires, the attached wired to the new switch, placed switch back into position, used nut driver to attach switch to the control unit. Rescrewed control unit in place with two screws.
turned on circuit breaker and tested. All good.
It is clear that this old Jenn Air range and be completely redone to good as new. All parts are available
All Instructions for models starting with 22116
1-15 of 58