Models > 22112 > Instructions

22112 Jenn-Air Cooktop - Instructions

All installation instructions for 22112 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 22112
31-45 of 75
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Burners were not regulating and they were just going on high

  • Customer: Debra from Syosset, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 3 of 5 people found this instruction helpful
I am not really handy. When the repair man came and gave me a price of $220 to repair two infinite switches, I looked up the cost of the switch and saw that it was easy to do...and it was! I saved $140 for doing it myself (no help from my husband).

First I turned off the power, unscrewed two screws and took the knob panel off. Wrote down the colored wires and then pulled them off the infinite switch (some needed pliers) and then i just put the wires back on the new switch...done...it works!

no problem...just wanted a fresh look

  • Customer: JANE from BALTIMORE, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
our cook top is so old, but no need to replace just yet. so I ordered new knobs to get a new look
thank you!

Burner on 'high' only, no other settings other than 'off'.

  • Customer: Janes from Marquette, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 2 of 3 people found this instruction helpful
SHUT OFF BREAKER! Remove exhaust grill and switch knob. Remove cooktop switch panel by removing two screws and sliding panel toward exhaust grill. Remove switch retainer nut with deep socket. Transfer wires one by one to new switch. Install new switch tightening retainer nut. Reinstall switch panel with two screws, push knob onto shaft. Turn on breaker.

Cleaners lost knob.

  • Customer: Virginia from Bothell, WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
I pulled off the other 3 old knobs. Pushed on the new ones, which pushed on hard, but work. They stick out farther than the originals. They look a little different, but only to me. No one else would notice.
The main part is, it works. A little spenty for my taste, but did not know where else to go and they arrived very quick.

smell of a dead animal

  • Customer: Duane from Niceville, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
The 15-year-old Jen-Air stove started smelling really bad. I thought it was a dead animal stuck in the exhaust tube which runs under the floor to the outside. I flushed it out with clorine bleach, but it was still bad. It turned out to the be the grease filter. I washed it every week in the diswasher, but it just was not enough to get it clean enough. Finally, the grease went rancid and smelled really bad. This "repair" took about 30 seconds.

Hmm, let's see, knob didn't match all my other new knobs

  • Customer: James from Devon, PA
  • Difficulty: Very Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 5 people found this instruction helpful
Oh this was a toughie and I was sweating it out.
With a delicate touch I removed the old knob and pushed on the new knob, 5 seconds

broken sens

  • Customer: Dennis from Mahomet, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
removeed the dial cover, paced the lens into the hole, slid the light and holder into place , 5 min job.

The original grease filter was damaged in our dishwasher (it is quite fragile) and needed to be replaced.

  • Customer: Martyn from Middletown, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover

The control knobs had been damaged by heat

  • Customer: Jery from Knoxville, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 3 people found this instruction helpful
Easily removed the old knobs and applied the new ones.

Numbers worn on old knobs

  • Customer: Bruce from Boca Raton, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
replaced old worn silver and white control knobs with new black ones.

ordered a new filter for the exhaust fan

  • Customer: Marijo from Bennett, IA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
The filter came and it was bent out of shape on 2 sides. My husband carefully tried to bend it back into shape. It is very flimsy and is not made as well as the one that was being used that was probably several years old. I did not want the hassel of returning the filter and trying to get a new one sent.

Change the Oil/Grease Filter

  • Customer: Yong from Houston, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
It is so easy. Once I found the right size of filter from the website, I ordered it right away. It came in 3 days and I just need to take out the old one and insert the new one. No instruction is necessary. By the way, the price of the filter is one third of that from Jenn-air.

Burner won't get hot

  • Customer: Robert from Golden, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
It was very simple. detached front switch panel by removing 4 screws inside top of oven door. Removed knob from old switch and removed nut holding switch to panel. Rotated switch panel to expose guts. replaced wires from old switch to new switch, screwed new switch to panel, replaced old knob. idea came from previous story at this website. Works great.

age & solivents melted the on pilot light lens

  • Customer: JAMES from McALESTER, OK
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
removed the wooden cutter block rt side top and the air exst.vent guard lf side then with a phileps driver 2 screws holding the control knob assm.in. both control knob assm.rt&lf come off the same way. just scraped out what that was left of the old lens stuck in new one and reatached light bulb holder. this bulb holder presses on and slides side ways to lock in place. then snaped control knob assm. back in and tighten the 2 screws. replaced vent guard & wooden cutter block. all was done.

Filter replacement.

  • Customer: Gerald from Maplefalls, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Remove and replace grease filter.
All Instructions for the 22112
31-45 of 75