Models > 21KPMAWAN6-32 > Instructions

21KPMAWAN6-32 Frigidaire Range - Instructions

All installation instructions for 21KPMAWAN6-32 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 21KPMAWAN6-32
166-176 of 176
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Left hinge broke in pieces

  • Customer: Marilyn from Yonkers NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
First I read other comments here; then checked youtube.com to see if there was a video - there was! Easily removed the stove door and the storage drawer to access the spring. Removed the spring and used screwdriver to remove 2 of 3 screws - third had a nut on back which required removal of the decorative panel next to the door. After applying Liquid Wrench, was able to use vise-grip to remove last bolt. Inserted new hinge, attached the spring to hinge and stove frame then inserted the 3 screws. Reattached the decorative panel and was done. Repklaced a hinge, not a stove!!!

no flame on broiler or oven

  • Customer: david from coalinga CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
replaced the ignitor switch, umplug oven turn off gas. removed racks unscrewed two screws in back of oven (inside of oven), removed bottom piece of oven, one screw for broiler cover removed, then two screws for ignitor, cut wires peeled off some excess covering, twisted the new ignitor to wires covered with attached cap tightly replaced two screws in ignitior, replaced one screw in broiler cover, two screws for bottom cover, replaced racks, pluged in turned gas and turned on stove ignitor lit up and started oven broiler, now i can cook again.

Oven heated slowly, then not at all.

  • Customer: Gregg from Roseburg OR
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
1. First, I read other people's instructions on this site, and that helped quite a bit. My own model was attached somewhat differently, so I was unable to replace the igniter in the same fashion as others. 2. Turned off the power to the oven after having done the non-electrical work: removed cover plate from bottom of inside oven (two screws in the back) to expose the igniter, and the heat shield from underneath the oven once the oven drawer was removed. Old, old screws so that was a bit of rolling around on the floor. 3. After that it was fairly easy: turned off the breaker, snipped one igniter wire from a plastic harness assembly under the oven and the other from the electrical core underneath the oven which was attached with a clamp. 4. Removed two screws to release the igniter. Now I could work on it in the light. Stripped the old wire underneath the oven, attached the old clamp to the other new wire, and then clamped one wire on and joined the other to the plastic harness wire with the screw cap. It was a bit of effort merely to get at things, but not difficult. Breaker back on, and the oven now works perfectly.

Igniter was past-due for a change-out!

  • Customer: Kevin P. from Chanute KS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Just opened up the oven and went to work. Really easy repair. Removed floor of oven with two thumb screws. Removed flame diverter plate from burner with one screw. Removed igniter with two screws. Marked top wire, then untwisted old wire nuts to remove the old igniter. Replaced with new igniter and used enclosed new wire nuts. Reassembly was simply the reverse of above. Only issue - I needed longer arms to comfortably reach back into the oven!

oven not heating

  • Customer: Mickey A from Linden MI
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Oven ignitor glowing but no flame . Tested ignitor w/ ohm meter reading 2.5ohms , should be 3.3 or higher to allow gas flow . Ordered new ignitor , replaces and jackpot !! Oven now fires and heats like new . Thanks for part . Cost , $50 instead of $150 .

Oven door hinges broken on range

  • Customer: Ross from Bridge Hampton NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
First off I want to thank Parts Select for getting the parts to me with-in 24 hours. This is incredible, I effected the repairs with-in 45 minutes thanks to the instructions I found on your site. As a result of Parts Selects web site I think I can handle any appliance repair going forward. Many thanks Ross,

The Ignitor had a brunt spot in the center.

  • Customer: Homer from Dayton OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I use a 1/4 in. socket and and ratchet to remove 2 screws and removed cover to get to sheild to unplug the two wire plug . Then used needle nose to remove two conectors from the gas valve.

Would not light.

  • Customer: John from Munster IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed oven racks. Removed oven bottom and flame diverter. removed two screws and cut wires. Spliced new wires and reassembled.

The oven igniter had become weak and would not ignite the burner.

  • Customer: JOYCE from DAVIS NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the oven racks. Unscrewed the two screws that held the oven bottom in. Removed the burner shield (one nut to remove). Removed the two screws holding the igniter in place. Removed the wires from behind and attached to the igniter. Removed the cover from corner that shields the wire and plug. Removed the plug. Removed entire igniter assembly. Cut and stripped the wires and wired back to the ends by using the wire nuts provided with the new igniter. Then just reversed the steps to reinstall the igniter! Yaay! It works fine. And I am a 66 year old woman with no help! I was very happy with the service and instructions provided by PartsSelect! Thanks!

Oven was slow to light and heat up

  • Customer: Mike from Roswell GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Replaced the oven igniter by removing the bottom oven tray (2 screws at back). Removed the 2 bolts that hold the igniter in place and cut the cables to it. Cut a little cable off the new igniter (cable supplied on the new igniter is long). Attached the new igniter with the 2 bolts and connected the cables together using the ceramic cable connectors supplied. Only thing to take care with is that you do not cut the cables too short and make sure to leave enough of a loop to join the cables together.

oven stop lighting

  • Customer: savannah from houston TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
had to cut to make a three end so it would plug in all three places
All Instructions for the 21KPMAWAN6-32
166-176 of 176