Models > 20237 > Instructions

20237 Jenn-Air Range - Instructions

All installation instructions for 20237 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 20237
46-60 of 219
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven would not heat

  • Customer: Rose from Modesto CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 2 of 2 people found this instruction helpful
First I removed the two screws that held the old element in place. Then I pulled the element out about 5 inches so I could reach and pull off the wire clips from the old element. I then attached the wire clips onto the new element and pushed back the wires into the insulated area and when the back plate matched up to the screw holes, I re-inserted the screws and tighten them down. The oven works great.

Oven would not heat

  • Customer: JOHN from SOUTH HOLLAND IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 2 of 2 people found this instruction helpful
First checked to see if there was power to the heating element. There was , so I knew the element was bad. I ordered a new heating element and it came in 3 days! I removed the two screws that held the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Reversed the procedure with new element. Turned on oven and my wife cooked a delicious meatloaf.

low and erratic temperatures

  • Customer: James from Holyoke MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
remove two screws, pull out element, diconnect two wires, toss old element,plug in wires to new element, replace two screws and viola- done

Now if you just sold faucet parts I'd be all set.

Baking element went out

  • Customer: Kelly from Poulsbo WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 2 people found this instruction helpful
The hardest part of the repair was getting the old cruddy screws out of the old element. They were sort of "baked-in". Once we got the screws out the rest was really easy. Just inserted the element prongs & screwed the new ones in. Ordering & receiving the part was a snap...I would recommend your company to anyone. Thank you.

Element failed

  • Customer: Andrew from Salem IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 5 people found this instruction helpful
Simple plug in.

The oven wouldn't heat because the bake element had burned a hole through the wall of the element tube.

  • Customer: Richard from Columbus NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
"First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and removed the two wires." from the burned out element. I plugged in the new element, reinstalled the new element and, 10 minutes start to finish, the oven heats again.
So easy even I can do it. !!!

Oven electrical element was broken (literally)

  • Customer: Madeleine from Gilford NH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
First we removed the two screws that hold the element in place. After pulling it from the back of the oven we did not realize that the clips that held the wires could be slipped off the 'tongues' of the element. Therefor we thought we had to cut the wires - which we did. After realizing that the clips came off, we went to the store and bought a box of new clips, stripped a small portion of the plastic on the wire to expose the wire and put it in the new clips and crimped them. Then slipped the new clips onto the new element, replaced it and put the old screws back. You wouldn't need to buy new clips (not expensive) if you know ahead that they can be removed from the old element and slipped onto the new one. We were amazed at how quickly the element arrived in the mail. Have bookmarked this sight for future repairs.

Needed Replacement Filters

  • Customer: Grady E from Vidalia GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
Remove Vent Cover, Remove Old Filter, Replace With New Filter, Replace Vent Cover, Repair Complete

Fan switch on top was broken off inside outer housing rendering all controls useless, worst of the fan.

  • Customer: kevin from wheaton IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
Cut power!
Removed old switch.Only problem was new switch had shifted the four 'spade' connectiors on back so when I was done fan and light switch was crossed.

Everything PartSelect had on their site was perfectly correct.

REALLY appreciated the way PartsSelect handled everything, I will be back for further help on other things.

element arc'd

  • Customer: ROBERT L from SUSSEX NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
needed hammer to help loose screws .pulled out and replaced leement

My oven light would NOT shut off

  • Customer: Glenn from Saginaw MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 6 people found this instruction helpful
Al lI had to do remove the oh swith & attach th e new on & push in place
It took about 5 min. to turn off the electric & to turn it back on.
Glen V

Any setting selected (1 thru 9) would result in the surface burner going to full hot

  • Customer: Randall from Eureka MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
Opened oven door, took four screws out of the front control panel, removed the two screws holding the burner control switch to the front panel, removed the wires from the old switch one at a time and installed them on the new switch. secured the new switch to the front panel, put the four screws back into the front panel, and closed the oven door. Real easy repair.

The old switch disintegrated

  • Customer: Edwin from Shalimar FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
Disconnected power from the stove. First I removed the down draft vent cover on stove top, then the two screws that held the switch plate in place, then used a wood chisel to pry the switch housing retaining washers off. Removed the remains of the old switch, Installed new switch, attached wires, and reinstalled switch plate. Placed vent cover on stove top and reconnected power.

Install Blower Motor

  • Customer: alice from Penns Grove NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 6 people found this instruction helpful
Since the motor is larger than the original, remove metal flange; shim one side of housing with 3 washers per screw and reseal..simple! Works great.

Interior window dirty (sealed unit; unable to clean)

  • Customer: Shelton from Decatur GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
Using exploded view and previous customers' comments, I disassembled the door. It was primarily a matter of finding all the screws. I recommend taking the door off first (I didn't), but watch your fingers. The hinges have very, very strong springs and you can hurt your or your helper's fingers if you're not prepared. The hardest part was keeping all the insulation in place while your're installing the assembly. I also replaced the gasket. That takes four hands, two to hold the gasket in place and two to reinstall the window assembly. To put the door back on the hinges, I pulled them out from the door at a 45-degree angle (takes some effort), put screwdrivers through holes in the hinges, and guided (with help) the door back on.
All Instructions for the 20237
46-60 of 219