The Stepped Washer is used to secure the wheels onto the shaft of a push mower. It attaches to the wheel axle. If broken due to wear/fatigue, the wheel will come off and the part should be replaced. I...
$3.99
In Stock
Order within the next 3 hrs and your part ships today!
This screw, also known as a shoulder bolt, is a genuine OEM replacement part for your lawn mower. This metal screw holds the starter grille in place against the rewing starter on your lawn mower. It r...
$4.99
In Stock
Order within the next 3 hrs and your part ships today!
This OEM Locking Ring holds components or assemblies onto a shaft or in a housing/bore when installed in a groove. Installation is rated as "Easy" by customers and will require pliers. The part secure...
$3.99
In Stock
Order within the next 3 hrs and your part ships today!
This is a genuine OEM replacement blade for use on Lawn Mowers. If the blade is too dull it will tear the grass instead of an even cut. A bent or damaged blade can cause serious damage or injuries. Yo...
$24.90
In Stock
Order within the next 3 hrs and your part ships today!
This is a compression spring that is used within various models of lawn mowers and is used to provide stability and extra control to the user during the operation of the equipment. This spring works i...
$3.99
In Stock
Order within the next 3 hrs and your part ships today!
The Shoulder Bolt is a 3/8-16 x 3-5/8 bolt, certified by the original equipment manufacturer. It is a metal bolt which is individually sold and comes in black. Installation requires a wrench or socket...
$4.99
In Stock
Order within the next 3 hrs and your part ships today!
This OEM Carburetor Bowl Gasket attaches between the carburetor bowl and carburetor in order to seal the parts together. This model is rubber, black, and comes individually sold. Installation is rated...
I lost two of the screws that hold the plastic Lawn Boy cowling to the Tecumseh lv195ea engine. I just replaced the lost screws with the newly ordered screws.
Tip mower onto side, raising side to be repaired. Empty gas tank if possible or use rags to prevent gasoline drips onto clean surfaces.
Remove wheel using a 1/2" socket. Remove wheel height assembly with 1/2" socket and open end wrench to hold nut below the deck. Position new spring arm over the slot on wheel height
... Read more assembly plate. Check opposite side to verify correct orientation if needed. Remove plastic cover from old lever using a small flat blade screwdriver. Slip onto new lever. Replace wheel height assembly. Replace wheel.
(2006)_WW_1.gif "Bail and Handle Assembly Diagram and Parts List for 260000001-260999999 - 2006 Toro Lawn Mower")
(2006)_WW_1.gif "Carburetor Diagram and Parts List for 260000001-260999999 - 2006 Toro Lawn Mower")
(2006)_WW_3.gif "Deck, Side Chute and Rear Door Assembly Diagram and Parts List for 260000001-260999999 - 2006 Toro Lawn Mower")
(2006)_WW_4.gif "Engine Diagram and Parts List for 260000001-260999999 - 2006 Toro Lawn Mower")
(2006)_WW_4.gif "Engine and Blade Assembly Diagram and Parts List for 260000001-260999999 - 2006 Toro Lawn Mower")
(2006)_WW_7.gif "Front Axle and Transmission Assembly Diagram and Parts List for 260000001-260999999 - 2006 Toro Lawn Mower")
(1999)_WW_9.gif "Page K Diagram and Parts List for 260000001-260999999 - 2006 Toro Lawn Mower")
(2006)_WW_8.gif "Rear Axle Assembly Diagram and Parts List for 260000001-260999999 - 2006 Toro Lawn Mower")
(2005)_WW_17.gif "Rear Bag Assembly Diagram and Parts List for 260000001-260999999 - 2006 Toro Lawn Mower")
(2004)_WW_12.gif "Recoil Starter Assembly Diagram and Parts List for 260000001-260999999 - 2006 Toro Lawn Mower")
(2006)_WW_12.gif "Transmission Assembly Diagram and Parts List for 260000001-260999999 - 2006 Toro Lawn Mower")
