Models > 1SF034PEW0 > Instructions

1SF034PEW0 Whirlpool Range - Instructions

All installation instructions for 1SF034PEW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 1SF034PEW0
1-15 of 18
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ignitor did not spark when turning the know

  • Customer: Richard from Lansing MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 9 people found this instruction helpful
Had to remove the 4 range knobs, and the oven knob and then the facie. Two screws under the end caps and two on each side from the back on each end. Design defect: one of these screws which attaches through the frame to the facie also attaches the support which holds up the range top. Take that one off last. Remove the two wires that attach to the oven light switch. After detaching the power supply to the defective ignition unit, it just pulls right off. Push the new switch on over the knob shaft and reassemble.

Left rear burner would not ignite

  • Customer: John from Perth Amboy NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 6 people found this instruction helpful
Removed the burner plates. Lifted up the range top. Removed the knobs. Unbolted the 2 rounded nuts at top of face plate. Removed the 4 screws that hold the face plate in place from behind. Un plugged the old switch and plugged in the new one and bam! The burner worked. Thanks, Super fast shipping! The part was here in less than 36 hours. John, N.J.

Right front gas burner ignitor wouldn't spark

  • Customer: Joseph from Lake George CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 7 people found this instruction helpful
I used the experience of another user posted on your web site. I removed all the gas control knobs and then I followed his instructions about removing the four phillps head screws that held the front plate in place. Once I had it loose and flipped the plate out, it was simple to disconnect the old ignitor switch and install the new one. Simply reversing the process put the range back in proper order. Took a little over 15 minutes to accomplish.

Burner broken due to excess oxidization

  • Customer: BRIAN from SCARSDALE NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
A part of the Left Front Burner of our range corroded and a hole opened up. This time, it was only one(1) of the four(4) burners I replaced but will plan to replace another one, the one in the back, in a year or so. Replacing the knobs was just for cosmetic reasons.

two burner ignitors would not function on cook stove

  • Customer: Warren from Las Cruces NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
1. ordered two new switches
2. installed switches
3. all ignitors work

Really appreciated the pictures of the parts--made selection very easy.

Replacing the bulb in the freezer side

  • Customer: Yafa (and David) from Bothell WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 4 of 5 people found this instruction helpful
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

oven light burnt out

  • Customer: William from Schwenksville PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 5 people found this instruction helpful
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

The Oven Would Not Light

  • Customer: RICHARD from GLOVERSVILLE NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 11 people found this instruction helpful
Removed the defective igniter, removing one screw and disconnected wire, replaced new ignighter in reverse fashion. And WELLA! The old oven works again!!

light bulb went out in my oven

  • Customer: Janet from Ada MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 4 people found this instruction helpful
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

burned oven bulb

  • Customer: Ivanka from Atlantra GA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 2 people found this instruction helpful
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Wrong oven thermostat

  • Customer: William from Lancaster CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Ordered "right" thermostat. Installed "right" thermostat.

The top seal on my Range broke

  • Customer: Clara from Missouri City TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The repair was really easy! I read a review where the gentleman had order the wrong size and that had me a little worried because I did not specify a size. There were three seals on my range so I figured if one broke I might as well replace all three. When I received the seals they were the right size and it took me less than five minutes to put them on. No tools needed because they had hooks on each end. Thanks a lot!

Light bulb failure

  • Customer: Grant from Alexandria VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

replaced oven lightbulb

  • Customer: peggy ann from forest city NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
very easy

Top oven seal sagging, no longer seals

  • Customer: Martin from Blanca CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Used 2 side seals to make a new top seal (no longer available). Cut the 2 new side seals to provide about 1/2" less length than the old top seal. Removed one of the end hooks and straightened the hook, removed the old silicone from the hook. Used high temperature silicone and the old hook to splice the cut ends together. Let cure over-night and reinstalled. Works like a champ.
All Instructions for the 1SF034PEW0
1-15 of 18