1CWGD5200VQ0 Whirlpool Dryer - Instructions

I came home from work to notice the dryer singing a different tune than usual. I opened the door and noticed that the tub wasnt turning. I popped the top of the dryer up to find a disentigrated belt. Fired up the computer and in a few minutes had ordered the $8 ($15 including shipping) replacement belt. 3 Days later took the shopvac and cleaned up the lint and broken belt pieces. Installed the new belt and was back in business with my 8 year old dryer. ** The only complaint comes from my wife who got her hopes up for a new front load washer and dryer** thanks partselect for saving my wallet in more than one way!

Remove two screws on top holding the filter frame.Use flat screwdriver to snap top at front off front panel.Swing top up and secure it against wall or tie in place. Remove screws holding front panel and kick panel to side panels.Did'nt remove back panel.Remove drive belt from pully wheel and then use belt to lift out drum.Use open end wrench on motor pully at rear and I used a socket set on the front of motor,Push down on wrench,counter clockwise,and hold the front pully from moving mine came right off. My dryer is over 10 yrs so the electric conection was changed but the instruction sheet explained how to change the wires,just follow the wire color,easy.

Everyone said changing a dryer belt was a piece of cake.They did not tell the truth it is a difficult job. I am a 52 year old female and I had a problem. You have to take the whole drum out. I finally completed the job but i had to prop the drum up with blocks so I could screw in the front panel. I think for those who want to change the belt I would go smoother with two people so the can hold things in place while the other one screws the panels back. I also think taking the dryer door off make the front panel a lot more easier to put in palce.

I found some help on-line that suggested some of the most likely causes. The on-line videos showed how to remove clips/panels to access the parts. Once I found the possibly failed parts, door switch and thermal fuse, I did a quick continuity check and found that the thermal fuse had an open circuit.

Took off the backplate of dryer, replaced fuse, done.

afer looking at the expoled views of the drier and locating the switch i checked to switch operation and found it wouldn't click.i ordered the switch,it arrived in just a couple days(right in the middle of the xmas holidays)i popped the top on the drier after finding 2 screws on the lint screen opening on top,2 screws mounted the switch,reassembled in reverse order and tested the drier.it was easy and with the new part in hand i saved aprox 200.00 dollars fixing it myself. p.s. please unplug the drier before starting any repairs...

My black very cool 15 year old Kithenaid electric dryer stopped working. No power. I tried the timer and it was still clicking like it was working. I opened the door then pushed the on button and heard a click which made me feel the door switch and on button were working. I replaced the cycling thermostat and thermal fuse and everything is fine. I wish i would have bought the other thermostat as I was right there and it was not that much. Dyer is working fine. This site is great. My repair guy moved out of state...I also disassembled the vent tube and vacuumed out all sorts of stuff and vacuumed the motor and all the area I could get to with the back, top and lower cover removed and waxed the dryer.

take'm apart put e'm back together

unplugged unit, removed the back panel replace thermo fuse and replace back panel, plugged electric cord back in and we were back in business. real easy fixx

quite simply I followed the path that was worn from years of use. it was very apparent the belt had broke. along with the belt there was a generic diagram for proper install. this was very helpful

I followed the video on the website, removing the back of the dryer, then located and removed the thermal fuse, replaced it with the new one..... Presto, it worked... Replaced the back of the dryer and was good to go... Thank you Part Select

Removed back cover,top,lower and upper front,and drum. Cleaned dust and dirt drom all of the removed parts and then removed the "lint tube". Took the tube apart to clean out dirt and lint, cleaned the lint off of the motor and blower wheel, and then removed the support wheels. Installed the "lint tube" and then the new support wheels with the new locks and then installed the new belt onto the drum. I had to support the drum in order to correctly line up the belt, and then installed the upper front panel. plugged in the power cord and started the motor to be sure everything was OK before closing up the rest of the cabinet. All was OK and the belt tracted perfectly. Installed the lower front panel, top, and the rear panel. Installed the gas connection, checked for gas leaks and installed the dryer back in place. checked operation with a batch of wet clothes and the dryer worked "better than new"!!! The instruction sheet was "spot on" for clarity and accuracy.

replaced thermo fuse. not the problem. not sure how to test for next step. timer, cycler tumbler all work just won't fire up.

Opened dryer top, disconnected door wireing, took off front panel, laid dryer on back, cleaned out lint and inside, put new belt on, and put parts back together. Dryer works fine now.

It was so easy. We looked up the information you said on your web site. Tested the parts and ordered 3 new parts. They went on easily. My dryer works like new!!!