1CWED5300VW0 Whirlpool Dryer - Instructions

Had to order idler lever and wheel as the one in the kit would not work. Best to buy part specific for your dryer. Repair was easy, just watch repair video. Sounds like new dryer again

Your customer service was great, but your video wasn't particularly helpful because of the extreme age of my dryer. For one thing, with these really old dryers, you don't have to slide the drum out at all; you just unscrew the front panel and slip the belt in that way. The printed diagram that came with the belt helped me figure how the belt slips through the pulley assembly, but the drawing could have been more clear. In spite of my bickering, I probably saved $50 fixing it myself.

Disconnect electric power, the top & cabinet are connected by 2 reusable locks about 4 inches from each front corner, use a thin flat putty knife or similar object, push inward on a lock while lifting gently on the front of the top piece, then let the top rest against the wall. ( a wire on each end of a safety switch for the dryer door may need disconnected) Remove a screw from each front corner of the cabinet, then pull upward on the loose front panel to access the drive motor, remove old belt. install new belt by lifting the front of the drum just high enough to allow the new belt, place groves of belt against the drum and around the motor pulley and belt tensioner, re-install cabinet front, (re-connect safety switch wires) return top and push down at cabinet locks.

I watched the video on PartSelect for this model. It was very easy to follow. The thermostat was mounted on a terminal lug which needed a little prying but not bad. Saved a least $140.

I checked the thermal fuse for continuity and had none.ordered part arrived next day. I took a picture with phone to idenify wires. installed in a short time.dryer works like new

removed the back of dryer and replaced the fuse with a screw driver,than I replaced the push to start button by unscrewing the top panel and replace the wiring onto the new part and install the new part very easy.works great saved a lot of money and the installion video was very helpful.

Before calling a repairman, I researched the problem at partselect.com. I am so glad that I did. It saved be a lot of money. I was able to narrow down the cause of "No Heat", and ordered a new Heating Element for the dryer thru partselect.com. The part arrived very quickly, and I was able to install the new part by first watching the installation videos at partselect.com. This could not have gone smoother, and I could not be happier. And, "no", I do not work for partselect.com. :)

Followed instructions on the installation video you had on line. Really easy and fixed the problem.

repair went just as describe in video.

I followed the video. Removed two screws by the lint filter, lifted up the 2 sides to the top of the dyer, removed the two screws by the door switch. It was that easy. The hard part came when I tried to remove the old switch that took the most time. I used the butter knife, since it was very flat I was able to lift it off. Put in the new switch, put all the parts back together again and it worked just fine. Thank you, PartSelect, I will come to you first. You saved me at least $150.00....

It was really easy I watched your video on how to do it the video went step by step and was very helpful

First I watched a instruction video online.. It made the job easy. I have done it before but I did not remember exactly how to proceed, After watching the video i knew exactly what screws needed to be removed and what tool I needed for each step. Anybody sees the video before tackling this job, they can't go wrong.

I followed the instructions almost exactly as the video and it was very simple. A few of the parts were a little difficult to get off but with a little tugging they popped off. After the initial installation I ran the dryer and the items didn't dry, so I ran it again and got the same result. Fortunately, not know I had already attempted to dry twice, my wife put a load in and it worked perfectly and has been since. Not sure the reason but it took 3 attempts before the heating element worked and I have a 12.5 year old drying that works good as new!

followed video on line

I did as your online movie said to do it. It is a big help and you can see that the belt, rollers and idler pulley is not a difficult job and you save yourself at least $100. Toughest part of job is putting back the nylon triangle things that hold the rollers on without breaking them.That is why I used the needlenose pliers. The triangle things that hold on the rollers have little tabs on them and I just gently pulled them outward and the triangles went right on.That repair kit from Whirlpool(builder of my Kenmore dryer)was a real bargain and everything fit perfectly. Bottom line is don't be afraid to try this repair. You will most likely succede. Go out to diner with the money you saved. Good luck, Mike