1CWED5100VQ0 Whirlpool Dryer - Instructions

after process of elimination ,figured had to be cut off switch followed simple instructions also watched your video..simple repair up and working again approx. 30 min. once i had kit. thanx 4 the help MIKE

I watched the video several times to make sure I got it right. The first thing that was very helpful was how to disassemble the top cover and front panel using a putty knife to disengage the detents. With the cover off I could acccess the belt and idler pulley. Replacing the belt was fairly easy as long as you note the way it threads through the idler pulley and drive pulley. I thought the video was excellent. It took me right to the problem and the fix. As a bonus the price for the belt was much lower from Parts Supply then from Sears. I've recommended this site to several others.

Just as your helpfull diagram of the dryer said, removed the rear panel,there it was, i recongnised it by the part you sent, pull it out of it's position, had a little truble figuring out the piece that fits on where the electric prongs are, after looking found out the piece was held on with a clip that goes inside the housing, Haaa. the rest was easy. Thanks,It works great. Dick

First I purchased the heating element, still no heat. Then I purchased the thermal fuse,still no heat. I have been pleased with the prompt shipment of the parts and the parts arrived safe. Thank you for service and time, not sure what to do now.I will recommend PartSelect to friends.

Unplug unit / removed back cover / went down , locating both parts to be replaced / simple one screw removal from each part / thermal fuse , one wire @ a time , reinstalled . / Cycling thermostat , 4 wires. Did one wire @ a time , reinstalled. / Putted back cover back on , plugged dryier back up, turned it on to run. To check for heat / yes, ran good as new. Later that day some more running , with damp clothes in it. Did it's job , dry.

your video was so helpful. It was exactly as shown. Thank You,we just had to replace a 14year old dishwasher and a 20 year old refrig. so it was great to repair the dryer.

I followed the repair method as described in the how to video it was as easy as that. Dryer is now working perfectly

Took the back off of the dryer, looked on "parts select" found what I thought might be the problem. Got the parts the next day. Put on new thermal fuse, then put on cycling thermostat. Wasn't sure which it needed, so put both on. Put the back of the dryer on hooked the gas up, hooked up to electric, & turned the dryer on. Back in business, everything works, dryer works as if nothing was wrong. Thanks to "parts select" saved me a repair bill.

I watched your video on how to replace the fuse.Wow it was a lot easier than I thought.I would highly reccomend anyone to watch the video before even trying to do any repairs.The dryer is working like a new one.By doing it myself saved me a lot of money.Thank you

Removed two screws at the top, removed two screws for the front panel, removed the broken belt, installed the new belt, followed the directions that were in the new belt package, and replaced all the panels and tested. It worked.

1.Unplugged power cord to Dryer. 2.Removed Dryer vent screen, unscrewed two screws located in dryer vent.3.Pried open top of dryer using putty knife. 4.Propped up top of dryer using 6 inch piece of wood resting on drum of dryer. 5.Removed screw holding door switch.6.Removed door switch from harness using putty Knife to pry apart connection. 7. Installed new door switch to harness and re-installed. 8.Removed wood used to prop open top, closed top, re-installed all screws, dryer vent and plugged dryer back up.

What a pain in the butt to route the belt thru the tensioner! There's room for only one hand in there. The guys who do this for a living must have some secret. My solution was to drill a 3/16 hole thru the side, make a j-hook from 8-32 threaded rod, use that and a wing nut to pre-load the tensioner, route the belt, then slowly back off the wing nut until the belt was tight. It works. . . .

Replaced the part. It just slid right in to the appropriate space on the dryer.

first I unplugged the dryer. Then I removed the back of the dryer with a 1/4" nut driver. with the back off using the same 1/4" nut driver I removed the one screw that holds the cycling t-stat slowly remove the t-stat and take one wire off at a time and plug it onto the new t-stat once all wires are replaced. place the t-stat back in and secure with the screw. Then put the back of the dryer back on. put the dryer vent hose back on. plug in and away you go. repair done. If that doesn't fix it. Then the next step is probably to check the gas valve coils. That is a little more difficult repair but not to hard.

Remove back pannel heating element easy to replace. Partselect has the best service ever...