Models > 16TA-3BK49 > Instructions

16TA-3BK49 Magic Chef Range - Instructions

All installation instructions for 16TA-3BK49 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 16TA-3BK49
1-15 of 26
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The grommets came apart metal from rubber.

  • Customer: Frank from Pierce ID
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 11 of 14 people found this instruction helpful
I replaced the broken grommets with the new ones. I purchased 8 so I would have back ups because I did not feel the new one would last either. I think they cost TOO MUCH but I could not haggle for price.

range top loose, grommets missing

  • Customer: joseph from wildomar CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 11 people found this instruction helpful
very easy to push each grommet into range top holes

burner would not light

  • Customer: Albert from Clewiston FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 9 people found this instruction helpful
saw burner tube was completely rusted at end and would not line up with burner. decided to go ahead and replace all three tubes. was easy to install, able to get a good cleaning job on unit in the process. works fine, wife is happy and that is what matters in a motorhome.

Oven rack missing

  • Customer: Pauline from Weedsport NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 3 people found this instruction helpful
Opened oven door, slid in rack , closed door...
Fit perfect....

missing gromet

  • Customer: Hal from National City CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 7 people found this instruction helpful
Pushed into hole by hand, really simple

THERMOSET W/FLANGE , FOR THE OVEN

  • Customer: John from Angleton TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Socket set, Wrench(Adjustable)
  • 4 of 8 people found this instruction helpful
THE FUEL LINES HAD TO BE CROSS OVER FROM THE FACTORY POSITIONS WHICH MADE ONE 3/8" TO SHORT. RESOLVED PROBLEM BY CUTTING THE SHEET METAL ON THE BACK OF THE STOVE TOP FROM 1" HOLE TO 1.5" BY CUTTING A SLOT IN THE LOWER PROTION OF THE HOLE WHICH WHEN BENT DOWN ALLOWED ME TO REBEND THE FUEL LINE DOWN GIVING ME THE NEEDED LENGTH TO RECONNECT THE FUEL LINE. NEW THERMOSET/FUEL VALVE WORK GREAT UPON COMPLETION. SINCERELY JOHN O.BEVERS

Needed a second oven rack for RV oven.

  • Customer: Michelle from Silver Springs FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 7 people found this instruction helpful
With a family of five a needed an extra oven rack as my RV oven is very small. After much aggravation between calling and going online to the manufacturer I still could not get any help. Even with locating the all important parts number. I was just about to give up when I was surfing around and found this website. Wow! What a relief! Not only did you show my where to find the part number, but I ordered it and got it within days. I spent more time on hold and online with the manufacturers customer service than anything else. From now on, no matter what I need, whether RV or home, I'm going staright to PartSelect. Thank You and my family thanks you too, as we wil be camping on Turkey Day and now I'll be able to get all the meal done at once! Happy Thanksgiving! God Bless

Old knob is broken

  • Customer: DONNA from WARREN PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
This item had to be returned. Didn"t fit. Our shaft is shorter, and the new knob would not stay on.

igniter would no longer work, it would stick

  • Customer: Randall from Rochester NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 5 people found this instruction helpful
pull knob off streight out. remove two phillips head screws, disconnect wire to disassemble. To reassemble reattatch wire to replacement igniter, screw in two phillips head screws and push on the knob.

Missing oven rack

  • Customer: Arlynn from Sagle ID
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Purchased a 1999 RV discovered the oven was misssing a rack and we were unable to use.
Located the part, ordering was easy. The rack arrived and fits perfect in the oven like it was made for it.

Thanks

I needed an additional rack for our RV oven

  • Customer: Wendi from Cypress CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
After some research in finding the information under the range hood, I did internet searches to find the appropriate replacement rack.
It fits great and we are thrilled to have the additional rack.

oven would light but not shut off at designated temp

  • Customer: Dan from Caseville MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 3 of 9 people found this instruction helpful
Make sure that gas is turned offf to appliance.I had to remove the top of the range and use adjustable wrench to loosen the two gas tubes. Then use screww driver to remove valve from gas feed tube ( oh - make sure to turn of gas at apppliance gas valve). I then had to use the adjustable wrnech for removing the flange.

Caution should be used when reinstalling the tubing. Also test all jionts with soapy water.

knob worn put

  • Customer: gail from bethany MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
easy replaced after giving proper model and serial numbers. They were very helpful sending pictures so i could choose which knob might work as they had two for the same model number. The person answering my call was very helpful. Also return of the wrong ones I ordered was easy and refund prompt. I would highly recommend this company.Gail from Mo.

Thermostat bulb was hanging loose

  • Customer: Willi from Old Saybrook CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 1 of 4 people found this instruction helpful
Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub

oven rack missing

  • Customer: Jimmy from Texarkana AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Odered rack on internet. Received in timely manner. Was the correct oven part. Very satisfied. Thank you.
All Instructions for the 16TA-3BK49
1-15 of 26