Models > 16RW-4K > Instructions

16RW-4K Maytag - Instructions

Installation Instructions for parts on models starting with 16RW-4K

These instructions have been submitted by other PartSelect customers and can help guide you through the repair with useful information like difficulty of repair, length of repair, tools needed, and more.

Models starting with 16RW-4K

All Instructions for models starting with 16RW-4K
1-15 of 22
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The grommets came apart metal from rubber.

  • Customer: Frank from Pierce ID
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 11 of 14 people found this instruction helpful
I replaced the broken grommets with the new ones. I purchased 8 so I would have back ups because I did not feel the new one would last either. I think they cost TOO MUCH but I could not haggle for price.

range top loose, grommets missing

  • Customer: joseph from wildomar CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 11 people found this instruction helpful
very easy to push each grommet into range top holes

Oven rack missing

  • Customer: Pauline from Weedsport NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 3 people found this instruction helpful
Opened oven door, slid in rack , closed door...
Fit perfect....

missing gromet

  • Customer: Hal from National City CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 7 people found this instruction helpful
Pushed into hole by hand, really simple

THERMOSET W/FLANGE , FOR THE OVEN

  • Customer: John from Angleton TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Socket set, Wrench(Adjustable)
  • 4 of 8 people found this instruction helpful
THE FUEL LINES HAD TO BE CROSS OVER FROM THE FACTORY POSITIONS WHICH MADE ONE 3/8" TO SHORT. RESOLVED PROBLEM BY CUTTING THE SHEET METAL ON THE BACK OF THE STOVE TOP FROM 1" HOLE TO 1.5" BY CUTTING A SLOT IN THE LOWER PROTION OF THE HOLE WHICH WHEN BENT DOWN ALLOWED ME TO REBEND THE FUEL LINE DOWN GIVING ME THE NEEDED LENGTH TO RECONNECT THE FUEL LINE. NEW THERMOSET/FUEL VALVE WORK GREAT UPON COMPLETION. SINCERELY JOHN O.BEVERS

Igniter wouldnt turn- knob spinning on shaft

  • Customer: Tim from Prosser WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Pull knob off igniter shaft, remove two screws, take out igniter, unplug wire. Reverse to install. Would have been very simple except the metal insert that is supposed to be inside the new knob was missing from the kit. I tried using the old insert in the new knob but it did not fit tight enough and would spin on the shaft. Had to use the old worn knob on the new igniter. Customer service said they don't carry the inserts. What? The brand new knob is useless! Needed to get the stove fixed so I didn't bother returning the entire kit. Oh well, stove works now!

Needed a second oven rack for RV oven.

  • Customer: Michelle from Silver Springs FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 7 people found this instruction helpful
With a family of five a needed an extra oven rack as my RV oven is very small. After much aggravation between calling and going online to the manufacturer I still could not get any help. Even with locating the all important parts number. I was just about to give up when I was surfing around and found this website. Wow! What a relief! Not only did you show my where to find the part number, but I ordered it and got it within days. I spent more time on hold and online with the manufacturers customer service than anything else. From now on, no matter what I need, whether RV or home, I'm going staright to PartSelect. Thank You and my family thanks you too, as we wil be camping on Turkey Day and now I'll be able to get all the meal done at once! Happy Thanksgiving! God Bless

igniter not working on magic chef stove on 60 foot yacht

  • Customer: Timothy from Vacaville CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
called and ordered the part. it arrived the next day. amazing. put it in and all was well./ another happy yacht owner.
Tim Wiest
Tim Wiest yacht Service

Top burners would not ignite

  • Customer: James from Brownwood TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Removed igniter wire, 2 screws, removed old igniter and reversed procedure, checked spark
and then lit burner. Easy, Easy

I needed an additional rack for our RV oven

  • Customer: Wendi from Cypress CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
After some research in finding the information under the range hood, I did internet searches to find the appropriate replacement rack.
It fits great and we are thrilled to have the additional rack.

Missing oven rack

  • Customer: Arlynn from Sagle ID
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Purchased a 1999 RV discovered the oven was misssing a rack and we were unable to use.
Located the part, ordering was easy. The rack arrived and fits perfect in the oven like it was made for it.

Thanks

Ignitor shaft and knob sheered

  • Customer: Tim from Santa Paula CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
This is a small RV cooktop. There is no pilot light but each burner will light using the spark type ingitor twist knob. Raise the front of the stove cooktop. It is on a hinge. Replace the ignitor assembly using existing screws. There is a very small anchor pin on the ignitor assy. which protrudes 1/16" from the base. The anchor pin hole had not been drilled into the stove face plate which prevents the ignitor assembly from twisting when engaged. So I drilled a 3/16 anchor pin hole exactly where required. It is important to be exact so as to align the installation screw holes in the face plate. These holes can be enlarged if need be however. Align the pin with the anchor hole and install the 2 existing screws. Attach the ignitor lead to the ignitor assy. and install the new knob. Close the stove top and start cooking.

oven would light but not shut off at designated temp

  • Customer: Dan from Caseville MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 3 of 9 people found this instruction helpful
Make sure that gas is turned offf to appliance.I had to remove the top of the range and use adjustable wrench to loosen the two gas tubes. Then use screww driver to remove valve from gas feed tube ( oh - make sure to turn of gas at apppliance gas valve). I then had to use the adjustable wrnech for removing the flange.

Caution should be used when reinstalling the tubing. Also test all jionts with soapy water.

oven rack missing

  • Customer: Jimmy from Texarkana AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Odered rack on internet. Received in timely manner. Was the correct oven part. Very satisfied. Thank you.

Ignitor was not functioning properly.

  • Customer: Kevin from Elk City OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I removed the igniter cable from the old knob. Removed 2 screws and the old knob, installed the new knob with 2 screws and plugged in the igniter cable. Works like a CHAMP!!! Must be an Oklahoma State University Football igniter and knob!! 2001 Big 12 Champions!!!!!
All Instructions for models starting with 16RW-4K
1-15 of 22