Models
>
14AI808H131
14AI808H131 Lawn Tractor - Overview
Models starting with 14AI808H131
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Lawn Mower Ground Drive Belt
PartSelect #: PS9172714
Manufacturer #: 954-04032B
3/8 x 36-1/8-inch
This ground drive belt (part number 954-04032B) is for lawn mowers.
Ground drive belt 954-04032B drives the transmission, which propels the lawn mower wheels.
Wear work glov...
$27.39
In Stock
Key
PartSelect #: PS9310468
Manufacturer #: 925-1745A
This manufacturer-certified Ignition Key comes in black/silver and is used in the ignition slot to turn on the engine. If your key becomes damaged or lost (which these small keys easily are), this pa...
$17.39
In Stock
Plastic Bushing .380 ID
PartSelect #: PS9167515
Manufacturer #: 941-0475
This is an authentic OEM part for Craftsman lawn and garden equipment. This bushing has an internal diameter of 0.380", is made of durable black plastic, is not part of an assembly or kit, and is sold...
$4.99
In Stock
Variable-Speed Belt
PartSelect #: PS9186148
Manufacturer #: 954-0467A
This is a Genuine replacement Belt designed for use with Riding Lawn Tractors/Mowers. This part is made out of Rubber and it is Sold Individually. This is the the Belt that drives your unit.
Make s...
$54.79
In Stock
Lock Ball Joint Assembly
PartSelect #: PS9171232
Manufacturer #: 923-0448A
The Lock Ball Joint Assembly is part of the steering mechanism, and the machine will not be able to steer without it. This part attaches to the steering block and drag link. Installation is rated as "...
$24.65
In Stock
Bell. Wash. .340 I.D. x .872 O.D.
PartSelect #: PS10006541
Manufacturer #: 736-0242
Sourced directly from the original manufacturer, this Bell Washer is made of gold-colored metal and is sold individually, not as part of a kit or assembly. It is used to provide spacing between variou...
$4.99
In Stock
Washer-Lock 5/16
PartSelect #: PS9311087
Manufacturer #: 936-0119
This Washer-Lock 5/16 is a silver, metal part that is sold individually and comes direct from the manufacturer. With a 5/16 Inch Interior Diameter and 1/2 Inch Outside Diameter, it is used to prevent ...
$4.99
In Stock
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
i NEEDED A DRIVE BELT FOR MY RIDING MOWER
1) DON'T ORDER FROM THESE IDIOTS.
2) THEY SENT THE WRONG BELT
3) THEY HAVE A CUSTOMER -NO- SERVICE NUMBER.
4) CAN'T GET A GOODS RETURN ONLINE
2) THEY SENT THE WRONG BELT
3) THEY HAVE A CUSTOMER -NO- SERVICE NUMBER.
4) CAN'T GET A GOODS RETURN ONLINE
Parts Used:
-
TERRY from OAK CREEK, WI
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
6 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Yardman / MTD wouldn't steer left, makes a popping and grinding noise when turning.
To disconnect the steering shaft to replace the bearing, there is a #3 Philips head screw on the underside of the deck which needs to be taken out. Chances are it hasn't been replaced before, so it is likely very tight. I ended up dropping the deck to allow for more room but it could probably be done with the deck in place the way I had t
... Read more
o do it. I had someone hold the steering wheel up top (not undoing the 13mm bolt holding the steering wheel in) and tried to unscrew the Philips, even after heating it with a torch still stripped out. The only way I could get the screw out was to take a pair of Vice Grips adjusted extremely tight to the outside of the screw and put the torch on it to heat it again. Then, turn the steering wheel to the left and when the Vice Grips get caught on the bottom of the mower, it will unthread the steering wheel from the screw. After the screw and washer are out *TAKE NOTE OF THE ORIENTATION OF THE WASHER*, I went to the hardware store and replaced the screw with a bolt that was 5/16 - 18 x .750 which was the closest length they had, took out the worn out bearing, popped in the new one, reinstalled the washer and bolt, then the deck. Even if you get the philips screw out without using Vice Grips, I would still recommend replacing it with a bolt.
Read less
Parts Used:
-
Patrick from Northville, NY
-
Difficulty Level:Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers, Socket set, Wrench set
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!