Models > 1413W0A > Instructions

1413W0A Roper Range - Instructions

All installation instructions for 1413W0A parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 1413W0A
16-28 of 28
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer would not activate

  • Customer: Andris from Sands Point NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 2 of 6 people found this instruction helpful
>removed 2 screws connecting the vent filter to the top lid of the unit (just in front of removable filter).
>Losing two screws at the back of the machine, just below control panel to allow free movement of the top lid on its hinges.
>Raise top lid & supported open.
>Now have free access to door switch (inside , front right fastened to front panel)
>removed the old switch
>fasten new switch (required new wire connector which was supplied with package) to existing wiring and replaced.
>Works perfectly!

Tines where falling off old rack

  • Customer: RONALD from EAST GREENWICH RI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 12 people found this instruction helpful
The dishwasher is 25 years old. Ordering the part was simple. Very good web site and user friendly. The shipment and delivery perfect. Part arrived as predicted. Tracking delivery was also perfect. Part was exactly what I needed. The only hitch was that there were no instructions for assembly, not even a drawing of the assembly to give a hint as how to assemble. Therefiore assembly took longer than it should have. However the diswasher is back in operation and I am pleased with the results.

water wouldn't run out of washer

  • Customer: James from Richmond VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Two screws holding top, unhook wire conector. remove cabinet,replace switch. Reassemble.

washer would fill with water but not start

  • Customer: Edward from Nanuet NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 10 people found this instruction helpful
took part top of washer saw switch replaced it not to difficult it is always easier when you have new one to look at

Replacement need for dish rack on our kitcheaid dishwasher

  • Customer: Beverly from East Troy WI
  • Difficulty: Really easy
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 2 of 10 people found this instruction helpful
Unable to solve problem as the rack did not fit even though it was for a kitchen aid dishwasher. Returned it as it did not fit our model

just wanted to replace the upper dish rack - the pieces have been rusting through

  • Customer: George from Monterey CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 10 people found this instruction helpful
no instructions came unfortunately, but it wasn't too difficult reverse engineering. took the upper rack out, disassembled it and put the new rack together using the old screws (since there were no screws either with the replacement rack). There are some extra parts I don't know quite what to do with - some type of additional separators, but the rack works fine without them.

over fill water

  • Customer: ronnie from meriden CT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
replace the water valve

Dryer door switch broken or burned out

  • Customer: James from Iota LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
My wife did the repair. Went on your website and watch the video on how to replace the switch and she was able to do it herself. I didn't mind at all. Saved $75.00 service charge.

the switch was broke

  • Customer: ralph from battle creek MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
unscrews 2 and pull panel down pulled 2 wires and 2 screws out and put in new switch in.

dryer wouldn't start

  • Customer: sean from easthampton MA
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I found on youtube that there are directions to repair. Dryer problems are usually one of three things, the door switch being one of them. i checked this last (should have been first). ordered the part( about 65% off sear's cost) and it came in one day! It went on really easy as long as you knew from repair video how to access inside. almost spent $400.00 on a new one.

Switch broken

  • Customer: Willie from Virginia Beach VA
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I was impressed with the fast time the part was delivered. The price was good too. The installation video and instructions did not match my dryer but it was helpful to some extent. The video and instructions being different was not ya'll's fault because of the age of the dryer. It took me so long to change the switch was because of the location and design of the switch. I got it though.

Washer quit running when lid was closed

  • Customer: Colleen from Indianapolis IN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
This repair took me longer because I was just giving it a try - I have no experience, although I tend to be "handy." I'm sure anyone with experience would rate this as "easy" and have taken only a short time. I had to watch the video several times to understand what to do - and the comments were helpful too. My washer is an OLD maytag, so I removed the front of the dash and pulled it forward to access the electronics. My switch had only 2 prongs, so I hooked up to the "lid closed" option on the new switch. It works perfectly now. Very pleased I gave it a try.

Stopped and would not restart / start.

  • Customer: Patricia from Duck WV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1)Shut off power supply to dryer. 2)Removed lint filter. 3)Removed two screws that secure filter duct to dryer top. 4)Lifted front of top to gain access to door switch. 5)Removed two switch mounting screws. 6)Removed the two power leads. 7)Reconnected power leads to new switch using "Normally Closed" terminal on switch. 8)Reversed the previous procedures to complete repair.
All Instructions for the 1413W0A
16-28 of 28