1375HW-KZW Admiral Wall Oven - Instructions

There was a lot of trepidation about starting this project. What if this is the wrong part? What if I hook it up wrong? What if the gas line is not properly secured when I'm done? This is why it took my 6 months to start this project. I hesitantly looked up my product number online and partselect.com returned three of the top ten results so I clicked it. One of the best moves I've made. When the product was shipped, I received an email with a video attached that explained how to install the igniter. This is what set partselect.com apart from everyone else and differentiated my experience from a "maybe i'll look around more next time" to "I will use partselect for all of my appliance part needs from now on" experience. Thank you for the quality customer care.

Remove oven door and bottom panel. Remove metal shield above the burner. Unscrew old igniter from brace. All this was straightforward. Then I found the old (long) igniter did not have a convenient plug that I could pull through the hole in the back of the oven. So I had to clip the two wires to remove the old igniter and stripped the insulation of these wires. Then I clipped the two wires of the new igniter since, unfortunately, I could not use the convenient plastic connector. I stripped the wires of the new igniter and connected both to the previously stripped wires coming through the hole from the back of the oven. I twisted on the ceramic wire nuts provided. It took 10-15 minutes or so to be confident these wire nuts wouldn't just fall off on their own. Then I stuffed the wire nut connections back through the hole, stuffed in all the insulation provided (necessary for the new (short) igniter!) and screwed the new igniter to the old brace. (I didn't need the new brace supplied or two long wires supplied.) Total time was about 70 minutes. The oven works well! This experience is much better than finding a repairman, scheduling the visit, etc.

look up part, read the diognosis, order part, watch repair vidioe, order part, install mystelf. success!

it was really simple with the kit and instructions that came with the kit everything i needed was in the kit, and hats off to you guys

followed video took 10 minutes, almost went anf bought a new stove

The only difficulty with following the supplied video, is that my ignitor did not come out as easily as a few turns of the screwdriver. The screws stripped as I tried to remove them, making them twirl in their holes. I had to apply back pressure for them to come off and free the ignitor for replacement. Other than that, the installation went smoothly, and the oven sprang to life within 10 seconds of turning it on.

I simply followed the "general" instructions from the online video "Partselect" provides and perused the instructions included in the kit. The OEM igniter was much longer than the replacement but the new part was spec'd just fine. It was necessary for me to open up the back of the stove in order to retrofit the igniter leads to the original block connector and install the heat resistant padding included in the kit. The additional necessary hardware fit very nicely inside the oven. The stove's oven fired up without any problems and spared me the expense of purchasing a new oven. Thank you very much "Partselect".

I removed and replaced the igniter. I described these symptoms on the web site and it detailed that90% of the time by installing a new igniter it will fix the described problem. So I ordered the part and installed the part and everything worked OK. The only tool I had to use was a screw driver to remove three screws. It took about half an hour. If I had to do it again it would take about 15 minutes.

Unplugged oven. Removed door,racks,and bottom shelf. Removed screws from ignitor and unplugged it from connection. Installed new ignitor with screws and plugged in to connection. Tucked wires behind insulation as they were before. Installed previously mentioned items and turned on to check. Worked great and am very pleased with PartSelect and the assistance they offer.

Ordered oven Igniter kit PS1573892 which cost $73.00. Received the kit with instructions easy to follow to install. I was surprised how easy it was to repair, with the help of my wife we did the job in about 2 hours, the oven now works great. I really saved a bundle of money doing this myself, a local repair service wanted $114.00 for the same part and $200.00 labor to install and this is the gospel truth. I am 96 years old. RMA Bluefield, WV

Take off oven door, remove racks, lift out bottom plate of oven, remove deflector shield, unbolt old igniter gently fish out the wire and plug from the back of the oven. Unplug and replace with the new igniter. re-assemble oven.

Followed the directions on the video. Very easy to do.

Once I noticed the oven failed to light, I checked the igniter and saw it was glowing. At that point I did some research and found that the igniter could still be bad even though it glowed. This was the most common cause of ovens not lighting. A bad igniter will not glow as bright as a new one. An igniter had to draw a minimum of 2.8 amps in order for the safety valve to open and supply gas to the burner. After checking the safety valve with an ohmmeter, I found it to be good, so I ordered a new igniter. Once I received the new part , it took about 20 minutes to install.

Replaced stripped screws with 632 by 3/8 bolts and nuts. Your video helped with the rest of the installation.

Unplug power cord to oven.Remove lower panel from inside of oven to access flame rail cover.Remove wingnut from cover to access flamerail and igniter.Using phillips head screwdriver,remove 2 screws from lower access plate located at rear of oven to access igniter wiring.Disconnect both wires, then using a nutdriver,unscrew and remove igniter from flamerail.To install, simply reverse instructions.It was extremely simple and fun to do.But most rewarding of all was the sense of accomplishment from doing the repair myself not to mention of course the money i saved not having to call a technician. Thanks guys!