Models
>
12AF
12AF Lawn Mower - Overview
Models starting with 12AF
Click on the best match to narrow your results.
- 12AF5690711 Troy-Bilt Lawn Mower (Lawn Mower)
- 12AF5690766 Troy-Bilt Lawn Mower (Troy-Bilt Lawn Mower Model 12AF5690766 Parts)
- 12AF569O711 (2004) Troy-Bilt Lawn Mower (Tuff-Cut 230 Walk-Behind Mower)
- 12AF569O766 (2004) Troy-Bilt Lawn Mower (Tuff-Cut 230 Walk-Behind Mower)
- 12AF569S790 MTD Lawn Mower (MTD Lawn Mower Model 12AF569S790 Parts)
- 12AF753B063 Troy-Bilt Lawn Mower (Troy-Bilt Lawn Mower Model 12AF753B063 Parts)
- 12AF753B063 (2002) Troy-Bilt Lawn Mower (12af753b063 9 Hp 33" Cut (2002))
- 12AF753B063 (2003) Troy-Bilt Lawn Mower (12af753b063 (2003))
- 12AF753B766 Troy-Bilt Lawn Mower (Troy-Bilt Lawn Mower Model 12AF753B766 Parts)
- 12AF754B766 Troy-Bilt Lawn Mower (Troy-Bilt Lawn Mower Model 12AF754B766 Parts)
- 12AF754B766 (2005) Troy-Bilt Lawn Mower (12af754b766 (2005))
Keep searches simple, eg. "belt" or "pump".
Front Lawn Mower Drive Wheel
PartSelect #: PS9455101
Manufacturer #: 734-04018C
This is a genuine OEM replacement part, it is sold individually.
This is the front wheel on the models shown below.
There are two of them on each mower.
The wheel has a ring gear on the inside whic...
No Longer Available
Mulching Blade
PartSelect #: PS9169783
Manufacturer #: 942-0741A
This is an authentic replacement part manufactured for use with Craftsman walk-behind lawnmowers. The blade is angled to allow the clippings to rotate through the cutting deck to produce fine clipping...
$32.37
In Stock
Lawn Mower Ground Drive Belt
PartSelect #: PS9172714
Manufacturer #: 954-04032B
3/8 x 36-1/8-inch
This ground drive belt (part number 954-04032B) is for lawn mowers.
Ground drive belt 954-04032B drives the transmission, which propels the lawn mower wheels.
Wear work glov...
$27.39
In Stock
Bell Blade Support
PartSelect #: PS17016260
Manufacturer #: 736-0524B-1
The Blade Support (Bell Blade Support) fits between the bottom of the blade and the blade bolt to provide support for the blade. It is installed underneath the cutting deck on the blade. Installation ...
$5.84
In Stock
Nut, Flange Lock, 1/4-20, Grf
PartSelect #: PS9299574
Manufacturer #: 712-04064
Also referred to as a Lock Nut or Flange Lock, this nut is designed for use with various lawn and garden equipment. The purpose of this part is to hold parts in place while resisting loosening when pr...
$3.99
In Stock
Side Discharge Deflector
PartSelect #: PS10005504
Manufacturer #: 731-04177
The Side Discharge Deflector, also known as a discharge chute, is a black plastic part used to direct glass clippings out from under the deck of the mower. This manufacturer-certified part has been ra...
$18.44
In Stock
Pin-Hinge
PartSelect #: PS9455906
Manufacturer #: 747-0710A
This hinge pin is an OEM part that is designed to hold the chute to the bracket of your lawn mower, allowing the shute to move upward and downward. It is silver, made of metal, and it is around 5 inch...
No Longer Available
Common Symptoms of models starting with 12AF
[Viewing 1 of 1]Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The treads on the front drive wheels were worn down to the point that they provided little traction.
Removed a single nut on each end of the drive shaft with the appropriate socket. Wheels then slipped off. Cleaned/polished the shaft with fine sandpaper, lubed with silicone spray, slid on the wheels and reinstalled the nuts with the same socket. Wheels were an exact fit and OEM quality. Done in 15 minutes start to finish.
Parts Used:
-
MICHAEL from Kennewick, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Front drive wheels were wore out
-
Ronald from WAYNE, MI
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Not the exact fit
I had to drill and tap the ends of the axle and put a 1/4” bolt in to fasten the wheels. The hubs were not the same. They fastened differently.
Parts Used:
-
Jay from GERRY, NY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!