Models > 1265H EZW > Instructions

1265H-EZW Admiral Oven - Instructions

All installation instructions for 1265H-EZW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 1265H-EZW
31-45 of 64
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

element burned out

  • Customer: luke from warren OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, that were clipped on. slipped them off connected the new element screwed it back into the oven.

element in oven burned out

  • Customer: Dorothy from Griggsville IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Went online and Googled for oven element by providing the serial and model number. Partselect popped up. I submitted the order and received and installed the new element within 5 days from start to finish. I recommend this website for replacement parts.

Element Got Corroded Then Failed (Broken)

  • Customer: Tom from Lancaster CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Connected the wires to new element, pushed wires back into the back wall, re-installed screws.

Heating element burned out

  • Customer: Ellis from West Valley City UT
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Found the model number, called the local parts store, they quoted $60 + $10 shipping because it was a warehouse order or something. So I came hear and got it for $42 + $7 shipping!

Turned off power, unscrewed the element, disconnected the clips from broken element, connected them to the new, screwed in the new element, and it was done

the element was burned!

  • Customer: Terry from Arlington TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
unscrew the old ones and replaced the new one - easy as that! Savings of over $300.00 if I need to buy a new one! Thanks for the speedy service after I ordered it.

oven element not wrk'n

  • Customer: Debbie from MT.VERNON IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Simply removed old element,2 screws,clean'd oven b/4 install'n new one,reconnect'd 2 wires,2 screws & yea oven wrks again. My husband was very happy as the oven is 34 yrs old,I just copied the model #,went 2 u'r web site,& we r very happy campers,so thank you very much.
Debbie A. Martin

took to long to preheat and food wasn't cooked on the bottom

  • Customer: Jessica from Lubbock TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
First, I want to say that this part arrived within 24 hours of placing the order. I was plesantly suprised. My husband did the repair and it was super easy. We had no problems.

Thanks PartSelect!

lower element burned out - had to replace

  • Customer: Steve from Highland Village TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
no instructions on how to replace element. first i removed the 2 screws that held the element to the oven. then i pulled the element out with the wires attached. at first i couldn't tell how the wires were attached - i thought they may have been soldered on. it took awhile for me to figure it out the wires were attached to a part that pulls up off the element part. no solder was needed. after i figured that out, easy to pull the part up off the element part.

Bake Element burned out

  • Customer: John from Lincoln Park NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Determining the correct bake element to order was the most difficult part. Once I received the part, it took me 2 minutes to unscrew the back panel, detach the wires, connect the new wires and re-connect the back pannel - turned the oven on to test - and we were all set just in time for Chistmas baking.

burned oven bulb

  • Customer: Ivanka from Atlantra GA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 2 people found this instruction helpful
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Oven wouldn't heat

  • Customer: Paul E. from Quincy IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
I took out the old part and we went on line and found everything from your PartSelect and ordered it. The part worked great and we received the part in two days. Thanks so much, you saved us lots of money and the oven works wonderful. I have told many people about your company and how much we like the help from you. Paul from Quincy, IL

Burned out element

  • Customer: Robert from Scotch Plains NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 3 people found this instruction helpful
Very easy since it was an exact match to the old burned out element.

Lower oven heating element burnt out.

  • Customer: Coreen from Hagerstown MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 3 people found this instruction helpful
I shopped around locally before shopping online. Parts Select provided me with significant time and money savings.

Turn off power. Remove the element. Installed the new element. Turned on the power. Easy... Easy... Easy...

Bottom heating element burned out/ broke.

  • Customer: Jessica from Macon GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
First, we cut the power to the oven and removed the oven racks. I removed the two screws holding the old heating element in (removed easily, I didn't need any WD-40) and pulled the element wiring out of the back of the oven. It took me a while to realize how the wiring was/is connected to the element, but once I did they came off fairly easily with a little coaxing from some pliers. On our model, the wiring thingums fit down onto the element prongs. So, you pull the straight up to remove them. Very technical terms here. After the wires and the new element were connected, I screwed the new element in, turned the power back on and the oven was is excellent working order again.

Heating elements (upper and lower ovens) would not achieve the proper temp

  • Customer: Charles from Independence KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the two screws on both elements, pulled the wires off, put the wires on the new elements and put the screws back in. Very easy, works perfect.
All Instructions for the 1265H-EZW
31-45 of 64